E2EC-CR5B1 Datasheet, PDF (2/9 Pages) Omron Electronics LLC – Subminiature Sensors with Long-distance Detection

Ratings and Specifications
E2EC
DC 2-Wire Models
DC 3-Wire Models
Item
Model E2EC-CR8D@ E2EC-C1R5D@ E2EC-C3D@
E2EC-X4D@
E2EC-CR5C1 E2EC-C2R5C1
Sensing distance 0.8 mm ±15%
1.5 mm ±10%
3 mm ±10%
4 mm ±10%
0.5 mm ±15%
2.5 mm ±10%
Set distance
0 to 0.56 mm
0 to 1.05 mm
0 to 2.1 mm
0 to 2.8 mm
0 to 0.3 mm
0 to 1.7 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 3.)
Standard sensing
object
Iron, 5 × 5 × 1 mm
Iron, 8 × 8 × 1 mm
Iron,
12 × 12 × 1 mm
Iron, 5 × 5 × 1 mm Iron, 8 × 8 × 1 mm
Response frequency
*1
1.5 kHz
1 kHz
Power supply volt-
age (operating volt- 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
age range)
5 to 24 VDC (4.75 to 30 VDC),
ripple (p-p): 10% max.
Current
consumption
---
10 mA max.
Leakage current
0.8 mA max.
---
Control
output
Load
current
Residual
voltage
5 to 100 mA
3 V max. (Load current: 100 mA, Cable length: 2 m)
NPN open-collector output,
100 mA max. (30 VDC max.)
1 V max. (Load current: 100 mA,
Cable length: 2 m)
Indicators
D1 Models: Operation indicator (red), Setting indicator (green)
D2 Models: Operation indicator (red)
Detection indicator (red)
Operation mode
D1 Models: NO
(with sensing object D2 Models: NC
approaching)
Refer to the timing charts under I/O Circuit Diagrams on page 5 for details.
NO
Refer to the timing charts under I/O
Circuit Diagrams on page 5 for details.
Protection circuits Load short-circuit protection, Surge suppressor
Surge suppressor
Ambient
temperature range
Operating/Storage: −25 to 70°C (with no icing or condensation)*2
Ambient
humidity range
Operating/Storage: 35% to 95% (with no condensation)
Temperature
influence
±20% max. of sensing distance at 23°C in the temperature range of −25 to 70°C
Voltage influence
±2.5% max. of sensing distance at rated voltage in the rated voltage ±15%
range
±5% max. of sensing distance at the
rated voltage range in the voltage
range of 4.75 to 30 V
Insulation
resistance
50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC for 1 min between current-carrying parts and case
500 VAC for 1 min between current-
carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s² 10 times each in X, Y, and Z directions
Destruction: 500 m/s² 10 times each in
X, Y, and Z directions
Degree of protection
IEC 60529 IP67,
In-house standards: oil-resistant (For Sensor Head only)
IEC 60529 IP64
Connection method Pre-wired Models (Standard cable length: 2 m)
Weight
(packed state)
Approx. 45 g
Case
Brass
Sensing
surface
ABS
Materials _Clamp-
ing nut
---
Brass
(nickel-plated)
---
Toothed
washer
---
Iron (zinc-plated)
---
Accessories
Amplifier Mounting Bracket, Instruction manual
Instruction manual
*1. The response frequency is an average value.
Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
*2. Incorrect operation may occur if there is a large temperature difference between the Sensor Head and the Amplifier Unit.
2