D2FD-2L0-1H Datasheet, PDF (2/5 Pages) Omron Electronics LLC – Dust Proof Ultra Subminiature Basic Switch

D2FD
Dust Proof Ultra Subminiature Basic Switch
Contact Specifications
Item
Model
Specification
Contact
Material
Gap (standard value)
Minimum applicable load (see note)
D2FD-2 models
Silver alloy
100 mA at 5 VDC
Note: For more information on the minimum applicable load, refer to Using Micro Loads.
Ratings
Crossbar
0.25 mm
D2FD-01 models
Gold alloy
1 mA at 5 VDC
Rated voltage
Model
125 VAC
30 VDC
Note: The rating values apply under the following test conditions.
1. Ambient temperature: 20 ± 2°C
2. Ambient humidity: 65 ± 5%
3. Operating frequency: 20 operations/min
Characteristics
D2FD-2 models
2A
2A
Resistive load
D2FD-01 models
0.1 A
0.1 A
Item
Model
D2FD-2 models
D2FD-01 models
Operating speed
1 mm to 500 mm/s
Operating frequency
Mechanical
Electrical
120 operations/min max.
20 operations/min max
Insulation resistance
100 MΩ min. (at 500 VDC)
Contact resistance (initial value)
30 mΩ max.
100 mΩ max.
600 VAC 50/60 Hz 1 min between terminals of same polarity
Dielectric strength (see note 2)
1,500 VAC 50/60 Hz 1 min between current carrying metal parts and ground
1,500 VAC 50/60 Hz 1 min between each terminal and non-current carrying metal part
Vibration resistance (see note 3) Malfunction
10 to 55 Hz, 1.5 mm double amplitude
Destruction
Shock resistance (see note 3)
Malfunction
1,000 m/s² max.
300 m/s² max.
Durability (see note 4)
Mechanical
Electrical
300,000 operations min. (at 60 ops./min.)
30,000 operations min. (at 20 ops./min.) 100,000 operations min. (at 20 ops./min.)
Degree of protection
IP6X
Ambient operating temperature
−20 to +70°C (at 60%RH max.) (with no icing)
Ambient operation humidity
85%RH max. (for +5 to +35°C)
Weight
Approx. 0.7 g (pin plunger, PCB terminal models)
Note: 1. The data given above are initial values.
2. The dielectric strength shown in the table indicates a value for models with a Separator.
3. For the pin plunger models, the above values apply for both the free position and total travel position. For the lever models, the values apply at the total travel
position. Contact opening or closing time is within 1 ms.
4. Consult your OMRON sales representative for testing conditions.
Terminals (Unit: mm)
● Solder Terminals
2.5±0.1
2.4
+0.1
–0.05
Dia.
2.4
+0.1
–0.05
1.2
2.2
4
4.8±0.1
5.08±0.15
5.08±0.15
12.8±0.15
1.7
1.5
5.7
2
0.5
0.4
4.4
6
● PCB Terminals
5±0.15
Two,1.2
+0.12
0
Dia.
5.5
1.6
1.5±0.1
Three, R0.8 _3.15
6.5±0.1
0.9
5.08±0.15
5.08±0.15
12.8±0.15
0.4
4.4
6
PCB Mounting Dimensions
(Reference)
Three, 1.2±0.05 Dia.
1.1±0.12
5.08±0.1
5.08±0.1
1.5±0.12
1.25±0.12
Mounting Holes (Unit: mm)
● Solder Terminals
Two, M2.3
4.8±0.1
2