V-16-1A6 Datasheet, PDF (15/16 Pages) Omron Electronics LLC – Miniature Basic Switch that Offers High Reliability and Security

V
Miniature Basic Switch
●Simulated roller lever
V-154-1@6
V-154-1@5
V-104-1@5
R3.5
t=0.5 *
PT A
32.6±0.8
8.1
V-104-1@4
2.8
OP
10.3±0.1
φ3.1^{+−00..1033} hole
15.9 _18.8
4.3 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8
37.8±0.8
2.8
(10)
t=0.5
10.3
Three, solder terminals
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-154-1@6
V-154-1@5
V-104-1@5
V-104-1@4
2.45N
0.25N
1.23N
0.14N
0.59N
0.06N
4.0mm
1.6mm
1.5mm
18.7±1.2mm
V
●Short hinge roller lever
V-155-1@6
PT
V-155-1@5
V-105-1@5
2.8
V-105-1@4
OP
10.3±0.1
t=0.5 *
20.1
A
8.1
3.1_{−+00..0133}
П3.4±0.15
22.2±0.1
27.8
37.8±0.8
φ4.8×4.8 *2
5.1
φ3.1^{+−00..1033} hole
2.8
Ê¢10Ê£
15.9 _18.8
Operating
characteristics
OF max.
RF min.
t=0.5
10.3
Three, solder terminals
PT max.
OT min.
MD max.
*1. Stainless-steel lever
OP
*2. Polyacetal resin roller
Stainless steel roller for heat-resistive models
Model
V-155-1@6
V-155-1@5
V-105-1@5
V-105-1@4
4.71N
0.49N
2.35N
0.49N
1.18N
0.15N
1.6mm
0.8mm
0.6mm
20.7±0.6mm
●Hinge roller lever
V-156-1@6
V-156-1@5
V-106-1@5
V-106-1@4
t=0.5 *1
PT
A
34±0.8
8.1
2.8
OP
10.3±0.1
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8
37.8±0.8
φ4.8×4.8 *2
5.1
φ3.1^{+−00..1033} hole
15.9 _18.8
Operating
characteristics
OF max.
RF min.
2.8
(10)
t=0.5
10.3
Three, solder terminals
PT max.
OT min.
MD max.
*1. Stainless-steel lever
OP
*2. Polyacetal resin roller
Stainless steel roller for heat-resistive models
Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Model
V-156-1@6
V-156-1@5
V-106-1@5
V-106-1@4
2.45N
0.25N
1.23N
0.14N
0.59N
0.06N
4.0mm
1.6mm
1.5mm
20.7±1.2mm
Precautions
★Please read "Common Precautions" for correct use.
Precautions for Safe Use
●Soldering
• Connecting to Solder Terminals
Complete the soldering at the iron tip temperature of 250 to
350°C (60W) within 5 seconds, and do not apply any external
force for 1 minute after soldering.
Be sure to apply only the minimum required amount of flux.It
may result in contact failure once the flux penetrates into the
internal part of the Switch.
• Connecting to Quick-connect Terminals #187
Insert the receptacle of quick-connect terminal #187 straight
toward the terminal.
Applying excessive external force horizontally or vertically may
cause deformation of terminals and may damage the
housings.
• Connecting to Quick-connect Terminals #250
Insert the receptacle of quick-connect terminal #250 straight
toward the terminal.
Applying excessive external force horizontally or vertically may
cause deformation of terminals and may damage the
housings.
Precautions for Correct Use
●Mounting
Use M3 mounting screw with plane washers or spring washers to
securely mount the Switch.Tighten the screws to a torque of 0.39
to 0.59N·m {4 to 6 kgf·cm}.
15