MSM6576 Datasheet, PDF (8/12 Pages) OKI electronic componets – Operatable at 0.9 V and 7-level Detector 4-Bit Microcontroller

¡ Semiconductor
MSM6576
ELECTRICAL CHARACTERISTICS
1.5 V operation
Backup flag (BUF) = "1"
The input of the constant voltage circuit is directly connected to the power supply (V_SS1).
(V_DD = 0 V, V_SS1 = –1.5 V (battery voltage) , V_SS2 = –3.0 V, f_OSC = 32.768 kHz, C_X = 35 pF, Ta = 25°C)
Parameter
Symbol
Condition
Min. Typ. Max. Unit Applied Pin
Power Supply Current 1
Power Supply Current 2
Oscillation Start Voltage
Output Current 1
Output Current 2
Input Current 1
*1 I_DD1
*1 I_DD2
–V_OSC
–I_OH1
I_OL1
–I_OH2
I_OL2
I_IH1
Level detector OFF
— 1.5 —
Level detector ON
— 13.5 —
Within 2 seconds
— — 0.9
V_O = –0.5 V
150 — —
V_O = –1.0 V
150 — —
V_O = –0.5 V
20 — —
V_O = –1.0 V
20 — —
V_I = 0 V, in the input state, _{3.75 7.5 15}
with pull-down resistor
mA
—
mA
—
V
V_SS1
PORT0 to PORT6*2
mA
SOUT, SCLK
mA
BD
PORT0 to
mA
PORT6 *2
Input Current 2
–I_IH2
V_I = –1.5 V, in the input state, _{3.75 7.5 15 mA}
with pull-up resistor
PORT0
Input Leakage Current
ÁI_ILÁ
V_I = 0 V, –1.5 V, in the input _{— —}
state, without pull-down resistor
PORT0 to PORT7*2
1 mA
SIN, SOUT, SCLK
Input Current 3
I_IH3
V_I = 0 V, with pull-down
RESET, TEST1
70 250 500 mA
resistor
to TEST3
Input Voltage
Level Detector Off Voltage
Level Detector Detecting
Voltage
Level Detector Settling Time
–V_IH
–V_IL
–V_LDoff
–V_LD6_H
–V_LD5_H
–V_LD4_H
–V_LD3_H
–V_LD2_H
–V_LD1_H
–V_LD0_H
t_SET
—
—
ADSTART = "0"
(ADOUT) = 6_H
(ADOUT) = 5_H
(ADOUT) = 4_H
(ADOUT) = 3_H
(ADOUT) = 2_H
(ADOUT) = 1_H
(ADOUT) = 0_H
ADSTART = "1", during
OUT ADSET execution
— — 0.3
V All input pins
1.2 — —
0 — 80 mV
725 742 759
841 858 875
958 975 992
1075 1092 1109 mV
1191 1208 1225
P7.1
1308 1325 1342
1425 1442 1459
— — 61 ms
Level Detector Conversion Rate
Comparator Offset Voltage
Comparator Input Voltage
Comparator Conversion Rate
f_LD
–V_CMPoff
–V_CMPin
f_CMP
—
—
–V_B = Battery voltage
—
——
——
V_B/2 —
——
100 Hz
15 mV
V_B V
100 Hz
P7.3, P7.2
*1 Depends on program. (Values in the above table are applied in the case where the software
duty is about 3%.)
*2 PORT0 = P0.0 to P0.3, PORT1 = P1.0 to P1.3, PORT2 = P2.0 to P2.3, PORT3 = P3.0 to P3.3,
PORT4 = P4.0 to P4.3, PORT5 = P5.0 to P5.3, PORT6 = P6.0 to P6.3, PORT7 = P7.0 to P7.3
8/12