|
RES-LVC Datasheet, PDF (1/2 Pages) Ohmite Mfg. Co. – Computer | |||
|
LVC Series
Low Value Chip
Ohmiteâs LVC Series low value chip
resistors are ideal for todayâs current
sense applications requiring low profile,
low cost solutions. Available in 0.5,
0.75, and 1 watt sizes, footprints are
1206, 2010, and 2512 size respectively.
These resistors are offered in ohmic
ranges from 0.10 to 4.7 ohms in stan-
dard 1% and 2% in E12 values depend-
ing on value.
The LVC Series resistors are well
suited for a variety of industrial and
commercial applications.
Appl i c a t i o n s
⢠Switching Power Supplies
⢠Cellular
⢠Telecom and Wireless
⢠Computer
⢠RF
F e at u r e s
⢠Industry Standard Sizes
⢠Terminal Barrier Resists Ag
Migration
⢠Working Temperature Range
is from -40°C to +125°C
⢠Designed for Automatic
Insertion
S ERIE S S P E C IFI C ATION S
Power Max.
Series Rating Current
LVC06 0.5W
32A
LVC20 0.75W 40A
LVC25 1.0W
45A
* E-12 values and 20, 25, 50
Resistance
Range*
10m-15m
18m-27m
33m-47m
50m- 4.7
10m-15m
18m-27m
33m-47m
50m- 4.7
10m-15m
18m-27m
33m-47m
50m- 4.7
TCR
ppm/°C
500
350
200
100
500
350
200
100
500
350
200
100
Resistance Tolerance
10mΩ ~ 22mΩ 2%
27mΩ ~ 4.7Ω 1%
c h a r a c t e r i s t i cs
Substrate Alumina 96%
Resistor Thick Film, Ni-Cr Alloy
Electrode Sn, Ni, Cu
Coating Epoxy resin
Max. Working Volts V = âPR (P = Rated Watts, R = Resistance
Value)
Derating 100% @ 70°C, Derates Linearly to Zero @
125°C
Operating temp. -40â ~ +125â
range
Soldering The recommended soldering condition for
both reflow and wave soldering is as follows:
Preheating: 150° ~ 180°C 60 ~ 120 sec.
Soldering: min. 230°C 30 ~ 40 sec.
Max. temp.: max. 260°C max. 10 sec.
Performance data
Moisture 60â±2â, 90%~95% RH,
resistance Rated voltage 1.5h ON,
0.5h OFF, 1000h
Temperature -40â (30min.)/+125â
Cycle (30min.), 5 cycles
Short Time Rated voltage x 2.5 for 5s
Overload
Endurance 70â±3â, Rated voltage
1.5h ON, 0.5h OFF, 1000h
Resistance to 260â±5â for 10±1s
Solder Heat
Terminal Bending width: 2mm for
strength 10s±1s, Glass epoxy
substrate with thickness of
1.6mm
Solderability 245â±5â for 3s±0.5s
Max. (A) Time applied: max.
Overload 10msec Interval: min. 60sec
Current
±(0.5%+0.0005Ω)
±(0.5%+0.0005Ω)
±(0.5%+0.0005Ω)
±(0.5%+0.0005Ω)
±(0.5%+0.0005Ω)
±(0.5%+0.0005Ω)
Min. 90% coverage
LVC06
LVC20
LVC25
I=â(32/R)
I=â(50/R)
I=â(64/R)
10
1-866-9-OHMITE ⢠Intâl 1-847-258-0300 ⢠Fax 1-847-574-7522 ⢠www.ohmite.com ⢠info@ohmite.com
|
▷ |