TDA6107AJF Datasheet, PDF (6/16 Pages) NXP Semiconductors – Triple video output amplifier

Philips Semiconductors
TDA6107AJF
Triple video output amplifier
9. Characteristics
Table 5: Characteristics
Operating range: T_j = −20 °C to +150 °C; V_DD = 180 V to 210 V; test conditions: T_amb = 25 °C; V_DD = 200 V;
V_oc(1) = V_oc(2) = V_oc(3) = ¹â„₂V_DD; C_L = 10 pF (C_L consists of parasitic and cathode capacitance); R_th(h-a) = 18 K/W; measured in
test circuit of Figure 9; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Unit
I_q
V_ref(int)
quiescent supply current
internal reference voltage (input
stage)
5.6
6
7.6
mA
-
2.5
-
V
R_i
input resistance
G
gain of amplifier
-
2.1
-
kΩ
73
81
89
∆G
gain difference
−4.2
0
+4.2
PSRR
power supply rejection ratio
f < 50 kHz
[1] _-
55
-
dB
α_ct(DC)
DC crosstalk between channels
Measurement output pin I_om; V_oc = V_oc(min) to V_oc(max)
I_om(offset)
offset current of measurement I_oc = 0 µA;
output (for three channels)
V_om = 1.8 V to 6 V
∆I_om/∆I_oc
linearity of current transfer
(for three channels)
I_oc = −100 µA to +100 µA;
V_om = 1.8 V to 6 V
I_oc = −100 µA to +10 mA;
V_om = 1.8 V to 4 V
Output pins V_oc(1), V_oc(2), V_oc(3)
V_oc(DC)
DC output voltage
I_i = 0 µA
∆V_{oc(DC)(offset)} differential DC output offset
I_i = 0 µA
voltage between two output pins
-
−50
-
dB
−50
-
+50
µA
−0.9
−1.0 −1.1
−0.9
−1.0 −1.1
76
87
97
V
−5
0
+5
V
∆V_oc(T)
∆V_{oc(T)(offset)}
output voltage temperature drift
differential output offset voltage
temperature drift between two
output pins
-
10
-
mV/K
-
0
-
mV/K
I_oc(max)
V_oc(min)
V_oc(max)
B_S
B_L
t_co(p)
maximum peak output current V_oc = 50 V to V_DD − 50 V
-
20
-
minimum output voltage
V_i = 4.5 V; at I_oc = 0 mA
[2] _-
-
10
maximum output voltage
V_i = 0.5 V; at I_oc = 0 mA
[2] _{VDD − 15 -}
-
small signal bandwidth
V_oc = 60 V (p-p)
-
5.5
-
large signal bandwidth
V_oc = 100 V (p-p)
-
4.5
-
cathode output propagation time V_oc = 100 V (p-p) square
[3] _-
50 % input to 50 % output
wave
60
-
mA
V
V
MHz
MHz
ns
∆t_co(p)
difference in cathode output
V_oc = 100 V (p-p) square
[3] _−10
0
propagation time 50 % input to wave
50 % output (between two
output pins)
+10
ns
t_oc(r)
cathode output rise time
V_oc = 50 V to 150 V square ^[3] 67
91
113
ns
10 % output to 90 % output
wave
t_oc(f)
cathode output fall time
V_oc = 150 V to 50 V square ^[3] 67
91
113
ns
90 % output to 10 % output
wave
9397 750 14728
Product data sheet
Rev. 02 — 28 April 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
6 of 16