 English |
|
|
|
|
|
|
|
| ISP1507ABS Datasheet, PDF (58/81 Pages) NXP Semiconductors – ULPI Hi-Speed Universal Serial Bus On-The-Go transceiver | |||
| |||
| ◁ |
NXP Semiconductors
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
14. Static characteristics
Table 46. Static characteristics: supply pins
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = â40 °C to +85 °C; unless otherwise speciï¬ed.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise speciï¬ed.
Symbol Parameter
Conditions
Min Typ
V(REG3V3)
V(REG1V8)
VPOR(trip)
ICC
voltage on pin REG3V3
voltage on pin REG1V8
power-on reset trip voltage
supply current
charge pump disabled
low-power mode; VBUS valid detector
disabled; 1.5 k⦠pull-up resistor on
pin DP disconnected
3.0 3.3
1.65 1.8
1.0 -
-
35
low-power mode; VBUS valid detector
disabled; 1.5 k⦠pull-up resistor on
pin DP connected
-
215
full-speed idle; no USB activity
-
10
high-speed idle; no USB activity
-
19
full-speed continuous data transmit;
[1] -
15
50 pF load on pins DP and DM
full-speed continuous data receive
[1] -
11
high-speed continuous data transmit;
[1] -
48
45 ⦠load on pins DP and DM to ground
high-speed continuous data receive
[1] -
28
charge pump enabled
IO(VBUS) = 8 mA; charge pump supply
current only
-
20
IO(VBUS) = 0 mA; charge pump supply
current only
-
300
ICC(I/O)
supply current on
pin VCC(I/O)
ULPI interface pins are static
-
-
Max Unit
3.6 V
1.95 V
1.5 V
85
µA
280 µA
-
mA
-
mA
-
mA
-
mA
-
mA
-
mA
23 mA
-
µA
1
µA
[1] A continuous stream of 1 kB packets with minimum inter-packet gap and all data bits set to logic 0 for continuous toggling.
Table 47. Static characteristics: digital pins
Digital pins: CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N and CHIP_SELECT_N; unless otherwise speciï¬ed.
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = â40 °C to +85 °C; unless otherwise speciï¬ed.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise speciï¬ed.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Input levels
VIL
LOW-level input voltage
VIH
HIGH-level input voltage
IIL
LOW-level input current VI = 0 V
IIH
HIGH-level input current VI = VCC(I/O)
ILI
input leakage current
-
-
0.7 Ã VCC(I/O) -
-
-
-
-
â1
+0.1
0.3 Ã VCC(I/O) V
-
V
1
µA
1
µA
+1
µA
Output levels
VOL
LOW-level output voltage IOL = +2 mA
-
-
0.4
V
ISP1507A_ISP1507B_1
Product data sheet
Rev. 01 â 19 May 2008
© NXP B.V. 2008. All rights reserved.
58 of 81
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese