|
NTE1890 Datasheet, PDF (2/6 Pages) NTE Electronics – Integrated Circuit NTSC Decoder for TV | |||
|
◁ |
Electrical Characteristics (Contâd): (VP = V1â23 = 12V, TA = +25°C unless otherwise specified)
Parameter
Symbol
Min Typ Max Unit
Chrominance Amplifier (Pin3)
Input Voltage (PeakâtoâPeak Value, Note 2)
Input Impedance
Input Capacitance
ACC Control Range
V3â23(pâp)
|Z3â23|
C3â23
55 550 1100 mV
â
8
â kâ¦
â
4
6 pF
30 â
â dB
Change of the Burst Signal at the Output over the Whole Control Range
â
â
1 dB
Gain at Nominal Contrast/Saturation Pin3 to Pin24 (Note 3)
13 â
â dB
Output Voltge (PeakâtoâPeak Value at Burst Signal of 300mV(pâp),
(Note 3)
V24â23(pâp)
â 240 â mV
Maximum Output Voltage Range (Pin24, PeakâtoâPeak Value)
Distortion of Chrominance Amplifier at V24â23(pâp) = 0.5V (Output)
up to V3â23(pâp) = 1V (Input)
Frequency Response Between 0 and 5MHz
Saturation Control Range
V24â24(pâp)
d
α24â3
â 1.7 â
V
â 3.0 5.0 %
â
â â2 dB
50 â
â dB
Input Current Saturation Control (Pin6)
Tracking Between Luminance and Chrominance Contrast Control
I6
â
â 20 µA
â
â
2 dB
CrossâCoupling Between Luminance and Chrominance Amplifier
(Note 4)
â
â â46 dB
SignalâtoâNoise Ratio at Nominal Input Signal (Note 5)
S/N
56 â
â dB
Phase Shift Between Burst and Chrominance at Nominal
Contrast/Saturation
â
â ±5 deg
Output Impedance of Chrominance Amplifier
Output Current
Reference Part (PhaseâLocked Loop)
|Z24â23|
I24
â 25 â
â¦
â
â 10 mA
Catching Range (Note 6)
âf
500 700 â Hz
Phase Shift for ±400Hz Deviation for fOSC (Note 6)
Reference Part (Oscillator)
â
â
5 deg
Temperature Coefficient of Oscillator Frequency (Note 6)
Frequency Variation when Supply Voltage Increases from
10V to 13.2V (Note 6)
TCOSC
âfOSC
â â1.5 â Hz/K
â 40 â Hz
Input Resistance (Pin22)
Input Capacitance (Pin22)
R22â23
C22â23
â 300 â
â¦
â
â 10 pF
Note 2. Indicated is a signal for a color bar with 75% saturation; chrominance to burst ratio is 2.2:1.
Note 3. Nominal contrast is specified as the maximum contrast â3dB and nominal saturation as the
maximum saturation â6dB.
Note 4. Cross coupling is measured under the following conditions:
S Input signals nominal.
S Contrast and aturation such that the nominal output signals are obtained.
S The signals at the output at which no signal should be available must be compared
with the nominal output signal at that output.
Note 5. The signalâtoânoise ratio is defined as peakâtoâpeak signal with respect to RMS noise.
Note 6. All frequency variations are referred to 3.58MHz carrier frequency.
|
▷ |