English
Language : 

NTE9370 Datasheet, PDF (1/2 Pages) NTE Electronics – Integrated Circuit HTL, Quad D-Type Flip-Flop
NTE9370
Integrated Circuit
HTL, Quad D–Type Flip–Flop
Description:
Four D–type flip–flops utilizing a common clock line make up the NTE9370. Each flip–flop has compli-
mentary passive pull up outputs with a single D input. This circuit is ideal as a quad latch for temporary
storage of 4–bit binary numbers.
Data is transferred from D inputs to outputs when the clock line is low. With the clock line high, output
data is held and D inputs are ignored.
Absolute Maximum Ratings:
Supply Voltage:
Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V
Pulsed (< 0.1sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5V to 16.5V
Voltage Applied to Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5V to +16.5V
Continuous Sink Current (TA = +25°C):
Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15mA
Surge (< 1sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Output Short Circuit Duration to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Operating Temperature Range, Topr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –30° to +85°C
Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55° to +100°C
Lead Temperature (During Soldering, 1/16” from case, 10sec max), TL . . . . . . . . . . . . . . . . . +300°C
Electrical Characteristics: (VCC = 12V ±1V unless otherwise specified)
Parameter
Symbol
Test Conditions
Input Threshold Voltage, Low
Input Threshold Voltage, High
Input Current, Low (1 Unit Load)
VIL Guaranteed input low threshold for all inputs
VIH Guaranteed input high threshold for all inputs
IIL VCC = Max, VIN = VOL1 max
Input Leakage Current (1 Unit Load) IIH VCC = Max, VIN = VCC
Output Low Voltage
Output High Voltage
Test Supply Voltage
VOL
VOH
VCC
VCC = Min, VIL = 5V VIH = 6.5V,
IOL = F.O. x U.L.
Min Typ Max Unit
5––V
– – 6.5 V
– – 2.1 mA
– – 10 µA
– – 1.5 V
10 – – V
11 12 13 V
Note 1. F.O. is fanout in unit loads (U.L.). A unit load is defined by the above input specifications.