English
Language : 

NTE726 Datasheet, PDF (1/2 Pages) NTE Electronics – Integrated Circuit Wide Band Amplifier
NTE726
Integrated Circuit
Wide Band Amplifier
Features:
D Exceptionally High Amplifier Gain: Power Gain at 4.5MHz/s – 75dB (Typ)
D Excellent Limiting Characteristics: Input Limiting Voltage (Knee) = 600µV (Typ) at 10.7MHz/s
D Wide Frequency Capability: 100kHz/s to > 20MHz/s
Absolute Maximum Ratings: (TA = +25°C unless otherwise specified)
Recommended Minimum DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Minimum Input Signal Voltage (Between Pin1 and Pin2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3V
Maximum Device Dissipation, PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mW
Operating Temperature Range, Topr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55° to +125°C
Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65° to +150°C
Lead Temperature (During Soldering, 1/16” from case, 10sec max), TL . . . . . . . . . . . . . . . . . +265°C
Electrical Characteristics: (TA = +25°C unless otherwise specified)
Parameter
Symbol
Test Conditions
Total Device Dissipation
Voltage Gain
Input–Impedance Components
PT VCC = 6V, Note 1
VCC = 7.5V, Note 1
VCC = 10V, Note 1
A
VCC = 6V, f = 1Mc/s, Note 2
VCC = 7.5V, f = 1Mc/s, Note 2
VCC = 7.5V, f = 4.5Mc/s, Note 2
VCC = 7.5V, f = 10.7Mc/s, Note 2
VCC = 10V, f = 1Mc/s, Note 2
Parallel Input Resistance
Parallel Input Capacitance
Output–Impedance Components
RIN VCC = 7.5V, f = 4.5Mc/s
CIN
Parallel Output Resistance
Parallel Output Capacitance
Noise Figure
Input Limiting Voltage (Knee)
ROUT
COUT
NF
vi(lim)
VCC = 7.5V, f = 4.5Mc/s
VCC = 7.5V, f = 4.5Mc/s
VCC = 7.5V, f = 4.5Mc/s
Min Typ Max Unit
66 90 121 mW
97 120 167 mW
150 190 255 mW
60 66 – dB
65 70 – dB
60 67 – dB
55 61 – dB
65 71 – dB
–
3
– kΩ
–
7
– pF
– 31.5 – kΩ
– 4.2 – pF
– 8.7 – dB
– 300 400 µV
Note 1. The total current drain may be determined by dividing PT by VCC.
Note 2. Recommended minimum DC supply voltage (VCC) is 5.5V. Nominal load current flowing into
Pin5 is 1.5mA at 7.5V.
 ▷