NTE7037 Datasheet, PDF (1/2 Pages) NTE Electronics – Integrated Circuit Module, 2 Output Positive Voltage Regulator for VCR

NTE7037
Integrated Circuit
Module, 2 Output Positive Voltage
Regulator for VCR
Features:
D 2 Outputs
D Output Voltage Select Function
Absolute Maximum Ratings: (T_A = +25°C unless otherwise specified)
Maximum DC Input Voltage, V_IN (DC) Max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
Maximum Average Output Current, I_O Max
V_O1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0A
V_O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0A
Maximum Peak Output Current (Note 1), I_O Max
V_O1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0A
V_O2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0A
Operating Case Temperature, T_C Max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +105°C
Maximum Junction Temperature, T_J Max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature Range, T_stg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –30° to +105°C
Thermal Resistance, Junction–to–Case, R_thJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7°C/W
Note 1. Peak Current: For 0.2sec Max.
Electrical Characteristics: (T_A = +25°C unless otherwise specified)
Parameter
Test Conditions
V_O1
Output Voltage Setting
Condition 1, Note 2
9.5±0.1
Output Cutoff Residual Voltage
Condition 1, Note 3
0.1
Ripple Voltage
Condition 1
5
Temperature Coefficient
Condition 1
0.02
Input Regulation
Condition 2
10
Condition 3
2
Load Regulation
Condition 4
50
Minimum Input–Output Voltage Difference Condition 5
1.2
V_O2
5.5±0.1
0.1
5
0.035
10
2
50
1.2
Unit
V
V Max
mV_p–p Max
%/°C Max
mV/V Max
mV/A Max
V Max
Note 2. Measurement must be made within 1 to 2 sec. after input switch is ON.
Note 3. When Pin7 is at High level (3V to 15V), V_O1, V_O2 are turned ON.
When Pin7 is at Low level (0.6V or less), V_O1, V_O2 are turned OFF.