NTE1172 Datasheet, PDF (1/3 Pages) NTE Electronics – Integrated Circuit Phase-Frequency Detector

NTE1172
Integrated Circuit
Phase–Frequency Detector
Absolute Maximum Ratings: (T_A = +25°C unles otherwise specified)
Supply Voltage, V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltage, V_I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Output Voltage, V_O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Power Dissipation, P_D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360mW
Operating Temperature Range, T_opr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –15° to +75°C
Storage Temperature Range, T_stg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40° to +125°C
Recommended Operating Conditions:
Parameter
Symbol
Supply Voltage
V_CC
Input Voltage, High Level
V_IH
Input Voltage, Low Level
V_IL
Test Conditions
Min Typ Max Unit
4.75 5.0 5.25 V
2.0 – 5.0 V
0 – 0.8 V
Electrical Charactersitics: (T_A = –15° to +75°C, GND = Pin7, Note 1 unless otherwsie specified)
Parameter
Symbol
Test Conditions
Min Typ Max Unit
Low Level Input Current (Pin1)
Low Level Input Current (Pin3)
Low Level Input Current (Pin11)
High Level Input Current (Pin1)
High Level Input Current (Pin3)
High Level Input Current (Pin11)
Low Level Output Voltage (Pin6)
Low Level Output Voltage (Pin12)
High Level Output Voltage (Pin6)
High Level Output Voltage (Pin12)
High Level Output Voltage (Pin2)
Low Level Output Voltage (Pin13)
I_IL
V_CC = 5.25V, V_IL(1) = 0.4V
–
I_IL
V_CC = 5.25V, V_IL(3) = 0.4V
–
I_IL
V_CC = 5.25V, V_IL(11) = 0.4V
–
I_IH V_CC = 5.25V, V_IH(1) = 2.5V
–
I_IH V_CC = 5.25V, V_IH(3) = 2.5V
–
I_IH V_CC = 5.25V, V_IH(11) = 2.5V
–
V_OL V_CC = 4.75V, V_IH(1,3) = 1.8V,
–
I_OL(6) = 20mA
V_OL V_CC = 4.75V, V_IH(1,3) = 1.2V,
–
I_OL(12) = 20mA
V_OH V_CC = 4.75V, V_IH(1,3) = 1.8V,
2.5
I_OH(6) = –1.6mA
V_OH V_CC = 4.75V, V_IH(1,3) = 1.8V,
2.5
I_OH(12) = –1.6mA
V_OH V_CC = 4.75V, V_OL(1,3) = 1.1V,
2.5
V_OL ^{IOH(2) = –1.6mA, IOL(13) = 20mA, Note 2}
–
– –4.8 mA
– –4.8 mA
– –1.6 mA
– 120 µA
– 120 µA
– 40 µA
– 0.4 V
– 0.4 V
–
–
V
–
–
V
–
–
V
– 0.4 V
Note 1. Pin numbers shown in ( ).
Note 2. This value is measured at Input State 9 of the truth table and varies depending on the situa-
tion of sequential logic.