LPC2364_10 Datasheet, PDF (8/59 Pages) NXP Semiconductors – Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC

NXP Semiconductors
LPC2364/65/66/67/68
Single-chip 16-bit/32-bit microcontrollers
Table 3. Pin allocation table …continued
Pin Symbol
Pin Symbol
Row J
1 P0[28]/SCL0
2 P0[27]/SDA0
5 P1[22]/MAT1[0]
6 V_SS
9 P2[13]/EINT3/
MCIDAT3/I2STX_SDA
Row K
1 P3[26]/MAT0[1]/
PWM1[3]
5 P1[23]/PWM1[4]/
MISO0
9 P0[11]/RXD2/
SCL2/MAT3[1]
10 P2[10]/EINT0
2 V_DD(3V3)
6 P1[26]/PWM1[6]/
CAP0[0]
10 P2[12]/EINT2/
MCIDAT2/I2STX_WS
Pin Symbol
3 P0[29]/USB_D+
7 P1[28]/PCAP1[0]/
MAT0[0]
11 -
3 V_SS
7 P1[27]/CAP0[1]
11 -
Pin Symbol
4 P1[19]/CAP1[1]
8 P0[1]/TD1/RXD3/SCL1
12 -
4 P1[20]/PWM1[2]/
SCK0
8 P0[0]/RD1/TXD3/SDA1
12 -
6.2 Pin description
Table 4. Pin description
Symbol
Pin
Ball
P0[0] to P0[31]
P0[0]/RD1/TXD3/ 46^[1]
SDA1
K8^[1]
P0[1]/TD1/RXD3/ 47^[1]
SCL1
J8^[1]
P0[2]/TXD0
98^[1]
C4^[1]
P0[3]/RXD0
99^[1]
A2^[1]
P0[4]/
I2SRX_CLK/
RD2/CAP2[0]
81^[1]
A8^[1]
P0[5]/
I2SRX_WS/
TD2/CAP2[1]
80^[1]
D7^[1]
Type
I/O
I/O
I
O
I/O
I/O
O
I
I/O
I/O
O
I/O
I
I/O
I/O
I
I
I/O
I/O
O
I
Description
Port 0: Port 0 is a 32-bit I/O port with individual direction controls for each
bit. The operation of Port 0 pins depends upon the pin function selected via
the pin connect block. Pins 12, 13, 14, and 31 of this port are not available.
P0[0] — General purpose digital input/output pin.
RD1 — CAN1 receiver input. (LPC2364/66/68 only)
TXD3 — Transmitter output for UART3.
SDA1 — I²C1 data input/output (this is not an open-drain pin).
P0[1] — General purpose digital input/output pin.
TD1 — CAN1 transmitter output. (LPC2364/66/68 only)
RXD3 — Receiver input for UART3.
SCL1 — I²C1 clock input/output (this is not an open-drain pin).
P0[2] — General purpose digital input/output pin.
TXD0 — Transmitter output for UART0.
P0[3] — General purpose digital input/output pin.
RXD0 — Receiver input for UART0.
P0[4] — General purpose digital input/output pin.
I2SRX_CLK — Receive Clock. It is driven by the master and received by
the slave. Corresponds to the signal SCK in the I²S-bus specification.
RD2 — CAN2 receiver input. (LPC2364/66/68 only)
CAP2[0] — Capture input for Timer 2, channel 0.
P0[5] — General purpose digital input/output pin.
I2SRX_WS — Receive Word Select. It is driven by the master and received
by the slave. Corresponds to the signal WS in the I²S-bus specification.
TD2 — CAN2 transmitter output. (LPC2364/66/68 only)
CAP2[1] — Capture input for Timer 2, channel 1.
LPC2364_65_66_67_68_6
Product data sheet
Rev. 06 — 1 February 2010
© NXP B.V. 2010. All rights reserved.
8 of 59