LMH6618_0711 Datasheet, PDF (7/28 Pages) National Semiconductor (TI) – PowerWise® 130 MHz, 1.25 mA RRIO Operational Amplifiers

Symbol
Parameter
Output DC Characteristics
V_O
Output Swing High (LMH6618)
(Voltage from V⁺ Supply Rail)
Output Swing Low (LMH6618)
(Voltage from V^− Supply Rail)
Output Swing High (LMH6619)
(Voltage from V⁺ Supply Rail)
Output Swing Low (LMH6619)
(Voltage from V^− Supply Rail)
I_OUT
Linear Output Current
R_O
Output Resistance
Enable Pin Operation
Enable High Voltage Threshold
Enable Pin High Current
Enable Low Voltage Threshold
Enable Pin Low Current
t_on
Turn-On Time
t_off
Turn-Off Time
Power Supply Performance
PSRR Power Supply Rejection Ratio
I_S
Supply Current (LMH6618)
Supply Current (LMH6619)
(per channel)
I_SD
Disable Shutdown Current
Condition
R_L = 1 kΩ to GND
R_L = 150Ω to GND
R_L = 1 kΩ to GND
R_L = 150Ω to GND
R_L = 150Ω to V^−
R_L = 1 kΩ to GND
R_L = 150Ω to GND
R_L = 1 kΩ to GND
R_L = 150Ω to GND
R_L = 150Ω to V^−
V_OUT = V⁺/2 (Note 6)
f = 1 MHz
Enabled
V_DISABLE = +5V
Disabled
V_DISABLE = −5V
DC, V_CM = −4.5V, V_S = 2.7V to 11V
R_L = ∞
R_L = ∞
DISABLE = −5V
Min
Typ
Max
Units
(Note 8) (Note 7) (Note 8)
111
100
126
457
430
526
110
121
mV
136
440
474
559
35
51
52
111
100
126
457
430
526
115
126
mV
141
450
484
569
45
61
62
±25
±35
mA
0.17
Ω
0.5
V
16
µA
−0.5
V
17
µA
25
ns
90
ns
84
104
dB
1.35
1.6
1.9
mA
1.45
1.65
2.0
103
140
μA
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)
Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: The maximum power dissipation is a function of T_J(MAX), θ_JA. The maximum allowable power dissipation at any ambient temperature is
P_D = (T_J(MAX) – T_A)/ θ_JA. All numbers apply for packages soldered directly onto a PC Board.
Note 4: Boldface limits apply to temperature range of −40°C to 125°C
Note 5: Voltage average drift is determined by dividing the change in V_OS by temperature change.
Note 6: Do not short circuit the output. Continuous source or sink currents larger than the I_OUT typical are not recommended as it may damage the part.
Note 7: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 8: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality
Control (SQC) method.
7
www.national.com