LM124 Datasheet, PDF (5/20 Pages) NXP Semiconductors – Low power quad op amps

Electrical Characteristics (Continued)
V⁺ = +5.0V, (Note 7), unless otherwise stated
Parameter
Conditions
Amplifier-to-Amplifier
Coupling (Note 11)
Output Current Source
Sink
Short Circuit to Ground
Input Offset Voltage
V_OS Drift
Input Offset Current
I_OS Drift
Input Bias Current
Input Common-Mode
Voltage Range (Note 10)
Large Signal
Voltage Gain
Output Voltage V_OH
Swing
Output Current
V_OL
Source
Sink
T_A = 25˚C
f = 1 kHz to 20 kHz, T_A = 25˚C
(Input Referred)
V_IN+ = 1V, V_IN− = 0V,
V⁺ = 15V, V_O = 2V, T_A = 25˚C
V_IN− = 1V, V_IN+ = 0V,
V⁺ = 15V, V_O = 2V, T_A = 25˚C
V_IN− = 1V, V_IN+ = 0V,
V⁺ = 15V, V_O = 200 mV, T_A = 25˚C
(Note 5) V⁺ = 15V, T_A = 25˚C
(Note 8)
R_S = 0Ω
I_IN(+) − I_IN(−), V_CM = 0V
R_S = 0Ω
I_IN(+) or I_IN(−)
V⁺ = +30V
(LM2902, V⁺ = 26V)
V⁺ = +15V (V_OSwing = 1V to 11V)
R_L ≥ 2 kΩ
V⁺ = 30V
(LM2902, V⁺ = 26V)
V⁺ = 5V, R_L = 10 kΩ
V_O = 2V
R_L = 2 kΩ
R_L = 10 kΩ
V_IN+ = +1V,
VV_I+N−=
= 0V,
15V
V_IN− = +1V,
VV_I+N+=
= 0V,
15V
LM124/LM224
LM324
LM2902
Units
Min Typ Max Min Typ Max Min Typ Max
−120
−120
−120
dB
20 40
20 40
20 40
mA
10 20
10 20
10 20
12 50
12 50
12 50
µA
40 60
40 60
40 60 mA
7
9
10 mV
7
7
7
µV/˚C
100
150
45 200 nA
10
10
10
pA/˚C
40 300
40 500
40 500 nA
0
V⁺−2 0
V⁺−2 0
V⁺−2
V
25
26
27 28
5
10 20
5
8
15
26
27 28
20
5
10 20
5
8
15
V/mV
22
V
23 24
20
5 100 mV
10 20
mA
5
8
Note 4: For operating at high temperatures, the LM324/LM324A/LM2902 must be derated based on a +125˚C maximum junction temperature and a thermal resis-
tance of 88˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM224/LM224A and LM124/LM124A can be de-
rated based on a +150˚C maximum junction temperature. The dissipation is the total of all four amplifiers — use external resistors, where possible, to allow the am-
plifier to saturate of to reduce the power which is dissipated in the integrated circuit.
Note 5: Short circuits from the output to V⁺ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
current is approximately 40 mA independent of the magnitude of V⁺. At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power
dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers.
Note 6: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP tran-
sistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the
IC chip. This transistor action can cause the output voltages of the op amps to go to the V⁺voltage level (or to ground for a large overdrive) for the time duration that
an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value
greater than −0.3V (at 25˚C).
Note 7: These specifications are limited to −55˚C ≤ T_A ≤ +125˚C for the LM124/LM124A. With the LM224/LM224A, all temperature specifications are limited to −25˚C
≤ T_A ≤ +85˚C, the LM324/LM324A temperature specifications are limited to 0˚C ≤ T_A ≤ +70˚C, and the LM2902 specifications are limited to −40˚C ≤ T_A ≤ +85˚C.
Note 8: V_O . 1.4V, R_S = 0Ω with V⁺ from 5V to 30V; and over the full input common-mode range (0V to V⁺ − 1.5V) for LM2902, V⁺ from 5V to 26V.
Note 9: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the input lines.
Note 10: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the
common-mode voltage range is V⁺ − 1.5V (at 25˚C), but either or both inputs can go to +32V without damage (+26V for LM2902), independent of the magnitude of
V⁺.
Note 11: Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be
detected as this type of capacitance increases at higher frequencies.
Note 12: Refer to RETS124AX for LM124A military specifications and refer to RETS124X for LM124 military specifications.
Note 13: Human body model, 1.5 kΩ in series with 100 pF.
5
www.national.com