ADC08061_09 Datasheet, PDF (5/16 Pages) National Semiconductor (TI) – 500 ns A/D Converter with S/H Function and Input Multiplexer

DC Electrical Characteristics
The following specifications apply for V⁺ = 5V unless otherwise specified. Boldface limits apply for T_A = T_J = T_MIN to T_MAX; all
other limits T_A = T_J = 25°C.
Symbol
Parameter
Conditions
Typical (Note Limits (Note
7)
8)
Units
(Limit)
V⁺ = 5.5V
Mode Pin
V_IH
Logic “1” Input Voltage
ADC08062 CS, WR, RD, A0 Pins
3.5
V (min)
2.2
V (min)
ADC08061 CS, WR, RD Pins
2.0
V (min)
V⁺ = 4.5V
Mode Pin
V_IL
Logic “0” Input Voltage
ADC08062 CS, WR, RD, A0 Pins
1.5
V (max)
0.7
V (max)
ADC08061 CS, WR, RD Pins
0.8
V (max)
V_IH = 5V
I_IH
Logic “1” Input Current
CS, RD, A0 Pins
WR Pin
0.005
0.1
1
µA (max)
3
µA (max)
Mode Pin
50
200
µA (max)
V_IL = 0V
I_IL
Logic “0” Input Current
CS, RD, WR, A0 Pins
Mode Pin
−0.005
µA (max)
−2
V⁺ = 4.75V
I_OUT = −360 µA
V_OH
Logic “1” Output Voltage
DB0–DB7, OFL, INT
I_OUT = −10 µA
DB0–DB7, OFL, INT
2.4
V (min)
4.5
V (min)
V_OL
Logic “0” Output Voltage
V⁺ = 4.75V, I_OUT = 1.6 mA
DB0–DB7, OFL, INT, RDY
0.4
V (max)
V_OUT = 5.0V
DB0–DB7, RDY
I_O
TRI-STATE Output Current
V_OUT = 0V
DB0–DB7, RDY
0.1
−0.1
3
µA (max)
−3
µA (max)
I_SOURCE
Output Source Current
V_OUT = 0V
DB0–DB7, OFL, INT
−26
−6
mA (min)
I_SINK
Output Sink Current
V_OUT = 5V
DB0–DB7, OFL, INT, RDY
24
7
mA (min)
I_C
Supply Current
CS = WR = RD = 0
11.5
20
mA (max)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its specified operating ratings. Operating Ratings indicate conditions for which the device is functional, but do not guarantee performance limits.
For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some
performance characteristics may degrade when the device is not operated under the listed test conditions.
Note 2: All voltages are measured with respect to the GND pin, unless otherwise specified.
Note 3: When the input voltage (V_IN) at any pin exceeds the power supply voltage (V_IN < GND or V_IN > V⁺), the absolute value of the current at that pin should
be limited to 5 mA or less. The 20 mA package input current specification limits the number of pins that can exceed the power supply boundaries with a 5 mA
current limit to four.
Note 4: The power dissipation of this device under normal operation should never exceed 875 mW (Quiescent Power Dissipation + the loads on the digital
outputs). Caution should be taken not to exceed absolute maximum power rating when the device is operating in a severe fault condition (e.g., when any input
or output exceeds the power supply). The maximum power dissipation must be derated at elevated temperatures and is dictated by T_JMAX (maximum junction
temperature), θ_JA (package junction to ambient thermal resistance), and T_A (ambient temperature). The maximum allowable power dissipation at any temperature
is PD_max = (T_JMAX − T_A)/θ_JA or the number given in the Absolute Maximum Ratings, whichever is lower. The table below details T_JMAX and θ_JA for the various
packages and versions of the ADC08061/2.
Part Number
T_JMAX
θ_JA
ADC08061/2BIN
105
51
ADC08061/2CIWM
105
85
Note 5: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices.
Note 6: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
5
11086 Version 6 Revision 2 Print Date/Time: 2009/07/15 15:48:35
www.national.com