LMH0002 Datasheet, PDF (2/5 Pages) National Semiconductor (TI) – SMPTE 292M / 259M Serial Digital Cable Driver

Absolute Maximum Ratings (Note 1)
Supply Voltage:
Input Voltage (all inputs)
Output Current
Storage Temperature Range
Junction Temperature
Lead Temperature
(Soldering 4 Sec)
Package Thermal Resistance
θ_JA 8-pin SOIC
θ_JC 8-pin SOIC
−0.5V to 3.6V
−0.3V to V_CC+0.3V
28mA
−65˚C to +150˚C
+150˚C
+260˚C
+125˚C/W
+105˚C/W
ESD Rating (HBM)
ESD Rating (MM)
5kV
250V
Recommended Operating
Conditions
Supply Voltage (V_CC – V_EE):
Operating Free Air Temperature (T_A)
LMH0002MA
LMH0002TMA
3.3V ±5%
0˚C to +70˚C
−40˚C to +85˚C
DC Electrical Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified (Notes 2, 3).
Symbol Parameter
Conditions
Reference
Min
V_CMIN Input Common Mode Voltage
V_SDI
Input Voltage Swing
V_CMOUT Output Common Mode Voltage
Differential
SDI, SDI
SDO, SDO
1.6 +
V_SDI/2
100
V_SDO Output Voltage Swing
SD/HD Input Voltage
SD/HD Input Current
I_CC
Supply Current
Single-ended, 75Ω load,
750
R_REF = 750Ω 1%
Single-ended, 75Ω load,
900
R_REF = 590Ω 1%
Min for SD
SD/HD
2.4
Max for HD
SD/HD = 0, (Note 5)
SD/HD = 1, (Note 5)
Typ
V_CC –
V_SDO
800
1000
3.7
45
38
Max
V_CC –
V_SDI/2
2000
850
1100
0.8
49
43
Units
V
mV_P−P
V
mV_P-P
mV_P-P
V
V
µA
mA
mA
AC Electrical Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified (Note 3).
Symbol Parameter
Conditions
Reference
Min
DR_SDI
t_jit
Input Data Rate
Additive Jitter
(Note 4)
1.485 Gbps
270 Mbps
SDI, SDI
SDO, SDO
t_r,t_f
Output Rise Time, Fall Time
SD/HD = 0, 20% – 80%,
(Note 6)
SD/HD = 1, 20% – 80%
400
Mismatch in Rise/Fall Time
(Note 4)
t_OS
Output Overshoot
(Note 4)
RL_SDO Output Return Loss
(Note 7)
15
Typ
Max Units
1485 Mbps
26
ps_P-P
18
ps_P-P
120
220
ps
560
800
ps
30
ps
8
%
20
dB
Note 1: "Absolute Maximum Ratings" are those parameter values beyond which the life and operation of the device cannot be guaranteed. The stating herein of
these maximums shall not be construed to imply that the device can or should be operated at or beyond these values. The table of "Electrical Characteristics"
specifies acceptable device operating conditions.
Note 2: Current flow into device pins is defined as positive. Current flow out of device pins is defined as negative. All voltages are stated referenced to V_EE = 0 Volts.
Note 3: Typical values are stated for V_CC = +3.3V and T_A = +25˚C.
Note 4: Specification is guaranteed by characterization.
Note 5: Maximum I_CC is measured at V_CC = +3.465V and T_A = +70˚C.
Note 6: Specification is guaranteed by characterization and verified by test.
Note 7: Output return loss is dependent on board design. The LMH0002 meets this specification on the SD002 evaluation board from 5MHz to 1.5GHz.
www.national.com
2