LZASERIES Datasheet, PDF (1/2 Pages) Nippon Precision Circuits Inc – Engineering Bulletin

Engineering Bulletin Tentative
No.804G / Mar.2012
Miniature Aluminum Electrolytic Capacitors
Low impedance, 105ˆ
˔Adoption of innovative electrolyte and new technologies
˔Very low impedance at high frequency
˔Endurance with ripple current: 4,000 to 7,000 hours at 105ˆ
˔Solvent resistant type
˔RoHS Compliant
˗SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105ˆ
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 35Vdc
ʶ20% (M)
(at 20ˆ, 120Hz)
I=0.01CV or 3ŸA, whichever is greater.
Where, I : Max. leakage current (ŸA), C : Nominal capacitance (ŸF), V : Rated voltage (V)
(at 20ˆ after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
tanЎ (Max.)
0.22 0.19 0.16 0.14 0.12
When nominal capacitance exceeds 1,000ŸF, add 0.02 to the value above for each 1,000ŸF increase.
(at 20ˆ, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
Z(-55ˆ)/Z(+20ˆ)
4
3
3
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the specified period of time at 105ˆ.
Time
П10 : 4,000hoursɹ
П12.5 : 5,000hoursɹ
П16 to 18 : 7,000hours
Rated voltage
6.3 to 10Vdc(П10)
6.3 to 10Vdc(П12.5 to18)
16 to 35Vdc
Capacitance change ʽʶ30% of the initial value
ʽʶ20% of the initial value
ʽʶ20% of the initial value
D.F.(tanЎ)
ʽ300% of the initial specified value ʽ200% of the initial specified value ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
ʽThe initial specified value
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after exposing them for 1,000 hours at 105ˆ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
6.3 to 10Vdc(П10)
6.3 to 10Vdc(П12.5 to18)
16 to 35Vdc
Capacitance change ʽʶ30% of the initial value
ʽʶ20% of the initial value
ʽʶ20% of the initial value
D.F.(tanЎ)
ʽ300% of the initial specified value ʽ200% of the initial specified value ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
ʽThe initial specified value
ʽThe initial specified value
˗DIMENSIONS [mm]
˔Terminal Code : E
Sleeve (PET : Dark blue)
L'
Vent
15min.
4min.
(П10)
(П12.5 to П18)
Gas escape end seal
ПD 10
12.5
16
18
Пd 0.6
0.6
0.8
0.8
F 5.0
5.0
7.5
7.5
ПD'
ПD+0.5max.
L'
L+1.5max.
˗PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E L ZA AAA E AA AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 680ŸF:681, 2,200ŸF:222)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 25V:250)
Series code
Category
Specifications in this bulletin are subject to change without notice.
NIPPON CHEMI-CON CORPORATION
1556
1