|
GPASERIES Datasheet, PDF (1/3 Pages) Nippon Precision Circuits Inc – MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Long life, Downsized, 125Ë
Upgrude!
(1"4FSJFT
ËDownsized, low impedance and high-ripple current version of GXE
series
ËSpecified ESR after endurance test
ËFor high ripple current automotive applications.
(Direct fuel injection and electric power steering etc.)
ËEndurance with ripple current : 3,000 to 5,000 hours at 125Ë
ËSolvent resistant type (see PRECAUTIONS AND GUIDELINES)
ËRoHS Compliant
GXE
Downsized
Higher ripple current
Higher temperature
LXZ
GPA
ËSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-40 to +125Ë
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
25 to 100Vdc
ʶ20% (M)
(at 20Ë, 120Hz)
I=0.03CV or 4ÂA, whichever is greater.
Where, I : Max. leakage current (ÂA), C : Nominal capacitance (ÂF), V : Rated voltage (V)
(at 20Ë, 1 minute)
Rated voltage (Vdc)
25V 35V 50V 63V 80V 100V
tanÐ (Max.)
0.14 0.12 0.10 0.10 0.08 0.08
When nominal capacitance exceeds 1,000ÂF, add 0.02 to the above value for each 1,000ÂF increase.
(at 20Ë, 120Hz)
Rated voltage (Vdc)
25V 35V 50V 63V 80V 100V
Z(-25Ë)/Z(+20Ë)
2
2
2
2
2
2
Z(-40Ë)/Z(+20Ë)
4
4
4
4
4
4
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20Ë after subjected to DC voltage with the rated ripple
current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours (3,000 hours for 25L and less) at 125 Ë.
Capacitance change ʽʶ30% of the initial value
D.F. (tanÐ)
ʽ300% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20Ë after exposing them for 1,000 hours at 125Ë without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ʽʶ30% of the initial value
D.F. (tanÐ)
ʽ300% of the initial specified value
Leakage current
ʽThe initial specified value
ËDIMENSIONS [mm]
ËTerminal Code : E
Sleeve (PET : Brown)
Vent
L'
15min.
4min. Gas escape end seal
ËPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E GPA AAA E AA AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 470ÂF:471, 1,000ÂF:102)
Lead forming·taping code
Terminal code
Voltage code (ex. 25V:250, 50V:500)
Series code
Category
Please refer to "Product code guide (radial lead type)"
ÐD 12.5ɹɹ14.5ɹɹ16 ɹɹ18
Ðd 0.6ɹɹ0.8 ɹɹ0.8 0.8
F 5.0 7.5 7.5 7.5
ÐD'
ÐD+0.5max.
L'
L+1.5max.
Product speciï¬cations in this catalog are subject to change without notice.Request our product speciï¬cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speciï¬cations.
(1/3)
CAT. No. E1001M
|
▷ |