ERLA181LIN901KR35M Datasheet, PDF (1/2 Pages) Nippon Precision Circuits Inc – LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS

LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS High ripple snap-ins, 85℃
RLA New!
Series
・Endurance with ripple current : 3,000 hours at 85℃
・High ripple current capability in a commercial frequency range
・High ripple current for inverter control like air conditioner
・Rated voltage range : 180 to 250Vdc, Capacitance range : 600 to 2,200μF
・Non solvent resistant type
・RoHS Compliant
RLB P239
Longer life
RLA
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Characteristics
-25 to +85℃
180 to 250V
±10% (K)
(at 20℃, 120Hz)
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 5 minutes)
Rated voltage (Vdc)
180 to 250V
tanδ (Max.)
0.15
(at 20℃, 120Hz)
Rated voltage (Vdc)
180 to 250V
Z(-25℃)/Z(+20℃)
4
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 3,000 hours at 85℃.
Capacitance change
≦±20% of the initial value
D. F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 85℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦±15% of the initial value
D. F. (tanδ)
≦150% of the initial specified value
Leakage current
≦The initial specified value
◆DIMENSIONS [mm]
●Terminal Code : LI (φ30, φ35) : Standard
Sleeve (PVC : Black)
Negative mark
PC board pin-out
(View from Solder side)
2-1.2×6
●Terminal Code : VS (φ30,φ35)
Sleeve (PVC : Black)
Negative mark
PC board pin-out
(View from Solder side)
10
Vent
L±2.5
4.5±1
The standard design has no plastic disc.
5±0.5
14.2±1
Vent
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E RLA AAA L I N AAA K AAA M
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex .800µF:801, 2,200µF:222)
Dummy terminal code
Terminal code ( LI,VS)
Voltage code (ex.180V:181, 200V:201)
Series code
Category
Please refer to "Product code guide (snap-in type)"
L±2.5
4.0±0.5
2-φ2
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
241
CAT. No. E1001P