|
EKZM160ELL152MJ20S Datasheet, PDF (1/3 Pages) Nippon Precision Circuits Inc – MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, 105â
KZMSeries
ã»Long-Life version of KZH series
ã»Endurance with ripple current : 6,000 to 10,000 hours at 105â
ã»Newly innovative electrolyte is employed to minimize ESR
ã»Rated voltage range : 6.3 to 50Vdc, Nominal capacitance range : 27 to 10,000µF
ã»Non solvent resistant type
ã»RoHS Compliant
KZN P136
Higher ripple
KZM
Longer life
KZH P142
âSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-40 to +105â
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
Endurance
Shelf Life
6.3 to 50Vdc
±20% (M)
(at 20â, 120Hz)
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
tanδ (Max.)
0.22 0.19 0.16 0.14 0.12 0.10
When nominal capacitance exceeds 1,000µF, add 0.02 to the value above for each 1,000µF increase.
(at 20â, 120Hz)
Z(-25â)/Z(+20â)
2 max.
Z(-40â)/Z(+20â)
3 max.
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20â after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the specified period of time at 105â.
Time
Ï5 &Ï6.3 : 6,000hours Ï8 : 8,000hours Ï10 to Ï18 : 10,000hours
Capacitance change â¦Â±25% of the initial value (6.3, 10Vdc : â¦Â± 30%)
D.F. (tanδ)
â¦200% of the initial specified value
Leakage current
â¦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20â after exposing them for 500 hours at 105â without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change â¦Â±25% of the initial value (6.3, 10Vdc : â¦Â±30%)
D.F. (tanδ)
â¦200% of the initial specified value
Leakage current
â¦The initial specified value
âDIMENSIONS [mm]
âTerminal Code : E
Sleeve(PET : Brown)
L'
Vent
(ExceptÏ5 &Ï6.3)
15min.
4min.
(Ï5 to Ï10)
(Ï12.5 to Ï18)
Gas escape end seal
ÏD 5 6.3 8 10 12.5 16 18
Ïd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
ÏD'
ÏD+0.5max.
L'
L+1.5max.
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KZM AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100µF:101, 1,000µF:102)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 10V:100)
Series code
Category
Please refer to "Product code guide (radial lead type)"
âRATED RIPPLE CURRENT MULTIPLIERS
âFrequency Multipliers
Frequency (Hz)
Capacitance (µF)
27 to 180
120
0.40
220 to 560
0.50
680 to 1,800
0.60
2,200 to 3,900
0.75
4,700 to 10,000
0.85
1k
0.75
0.85
0.87
0.90
0.95
10k
0.90
0.94
0.95
0.95
0.98
100k
1.00
1.00
1.00
1.00
1.00
Note : Tâ he endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5â rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
139
CAT. No. E1001N
|
▷ |