|
APXF2R0ARA681MF61G Datasheet, PDF (1/2 Pages) Nippon Precision Circuits Inc – Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte | |||
|
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
PXF NPCAPTM-
Upgrade!
Series
ã»Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
ã»Rated voltage range : 2 to 10Vdc, Capacitance range : 120 to 1,000µF
ã»Case size range :Ï5Ã3.9L toÏ8Ã7.7L
ã»Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
ã»Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
ã»RoHS Compliant
ã»Halogen Free
âSPECIFICATIONS
PXF
Lower ESR
PXE P40
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105â
2 to 10Vdc
±20% (M)
Rated voltageÃ1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20â, 120Hz)
(at 105â)
(at 20â after 2 minutes)
0.12 max.
(at 20â, 120Hz)
Z(-25â)/Z(+20â)â¦1.15
Z(-55â)/Z(+20â)â¦1.25
(at 100kHz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after the rated voltage is applied for 15,000 hours
(E40, E46, F45 : 3,000 hours ) at 105â.
Appearance
No signiï¬cant damage
Bias Humidity
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjecting them to the DC rated voltage at
60â, 90 to 95% RH for 1,000 hours (E40, E46, F45 : 500 hours ) .
Appearance
No signiï¬cant damage
Surge Voltage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage speciï¬ed at 105â for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No signiï¬cant damage
Failure Rate
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
0.5% per 1,000 hours maximum (Conï¬dence level 60% at 105â)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105â.
âDIMENSIONS [mm]
âMARKING
âTerminal Code : A
W
0.3max.
A±0.2
L±0.3 (Note)
Note : L+0.1/-0.2 for E40, E46 and F45
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXF
A RA
M
G
Size Code ÏD L A B C
W
P
E40
5 3.9 5.3 5.3 5.9 0.5 to 0.8 1.4
E46
5 4.5 5.3 5.3 5.9 0.5 to 0.8 1.4
E61
5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
F45 6.3 4.4 6.6 6.6 7.2 0.5 to 0.8 1.9
F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H70
8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
H80
8 7.7 8.3 8.3 9.0 0.7 to 1.1 3.1
EX) 2.5V390µF
F69A
390
2.5V
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 330µF:331, 1,000µF:102)
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
38
CAT. No. E1001P
|
▷ |