APSG250ELL331MJB5S Datasheet, PDF (1/2 Pages) Nippon Precision Circuits Inc – Super low ESR, high ripple current capability

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
PSG NPCAP^TM-
Upgrade!
Series
・Super low ESR, high ripple current capability
・Endurance: 15,000 to 20,000 hours at 105℃
・Rated voltage : 16 to 25Vdc
・RoHS Compliant
・Halogen Free
PSG
Downsized
PSF P52
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
-55 to +105℃
16 to 25Vdc
±20% (M)
Rated voltage(V)×1.15
I=0.2CV or 500µA, whichever is greater
Where, I : Leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours
(20, 25V : 15,000 hours) at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
●Terminal Code : E
F05,F08,H06,H08
Coated Case
L'
15min.
HB5,H16,H20,JB5,J16,J20
Coated Case
4min.
L'
15min.
4min.
Size code F05 F08 H06 H08 HB5 H16 H20 JB5 J16 J20
φD
6.3
8.0
10.0
φd
0.45
0.6
F
2.5
3.5
5.0
φD'
φD+0.5max.
L'
L+1.0max. (Note1)
L+1.5max.
Note1 : L+1.2 max. for 16V270µF (Rated ripple
current 5,080mArms).
◆MARKING
EX) 16V150µF
G ^6D6
150
16^V
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
48
CAT. No. E1001P