APSF2R0ESS102MF08S Datasheet, PDF (1/2 Pages) Nippon Precision Circuits Inc – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Upgrade!
Radial Lead
@Super low ESR, high ripple current capability
@ESR 5mO max. (2 & 2.5Vdc)
@Longer life (5,000 hours at 105C)
@ESR after endurance is specified within the initial spec (2 & 2.5Vdc)
@Rated voltage range : 2 to 16Vdc
@RoHS Compliant
@Halogen Free
PSF
Lower ESR
PSE
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-55 to +105C}
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
2 to 16Vdc
P20% (M)
Rated voltage(V)B1.15
I=0.2CV or 500MA, whichever is greater
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
0.10 max.
(at 20C, 120Hz)
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 5,000 hours
at 105C.
Appearance
No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)
[The initial specified value
ESR
2 & 2.5Vdc : [The initial specified value
16Vdc : [150% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)
[The initial specified value
ESR
2 & 2.5Vdc : [The initial specified value
16Vdc : [150% of the initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)
[The initial specified value
ESR
2 & 2.5Vdc : [The initial specified value
16Vdc : [150% of the initial specified value
Leakage current
[The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm]
@Terminal Code : E
F05, F08, H08 ^{Coated Case}
L'
FA5, HB5, JB5 ^{Coated Case}
15min.
(F05, F08, H08)
4min.
(FA5)
(HB5, JB5)
Size code
fD
fd
F
fD'
L'
F05 F08
6.3
0.45 0.6
2.5
L+1.0max.
FA5 H08 HB5 JB5
8.0
10.0
0.5
0.6
3.5
5.0
FD+0.5max.
L+0.3max. L+1.0max. L+1.5max.
?MARKING
EX) 2.5V560MF
F ^6D6
560
2.5^V
L'
15min.
4min.
(1/2)
CAT. No. E1001K