UZT1C100MCL1GB Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZT 4.5mmL Chip Type, Wide Temperature Range
series
Chip type with 4.5mm height, operating over wide temperature
range of – 40 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WT
Smaller
ZT
Smaller
Specifications
ZG
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Performance Characteristics
– 40 to +105°C
6.3 to 50V
0.1 to 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
6.3
0.38
10
0.32
16
0.20
25
0.16
35
0.14
50
0.14
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio
Z– 25°C / Z+20°C
6
5
3
3
3
3
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
10
10
6
6
4
4
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be
met when the capacitors are restored to
20°C after the rated voltage is applied for
1000 hours at 105°C.
Capacitance
change
tan δ
Leakage current
Within ±25% of the initial capacitance value (16V or less)
Within ±20% of the initial capacitance value (25V or more)
300% or less than initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which
is maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10µF)
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
Voltage mark for 6.3V is 6V .
4.5
+0.1
–0.2
0.5 to 0.8
Positive
Negative
(mm)
φD _{4 5 6.3}
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UZ T 1C 1 0 0 MC L 1GB
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
4
19
5
26
5
32
6.3
52
10
1A
5
24
5
30
6.3
40
16
1C
4
16
5
26
6.3
35
6.3
44
25
1E
4
11
5
20
6.3
33
6.3
42
35
1V
4
13
5
22
6.3
36
50
1H
4
0.9
4
2.2
4
2.8
4
3.3
4
5.4
4
9.6
4
12
5
16
6.3
26
Case size Rated
φ D (mm)
ripple
Rated ripple current (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UX(p.158), UJ(p.164) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100C