UZT1A100MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZT 4.5mmL Chip Type, Wide Temperature Range
series
Chip type with 4.5mm height, operating over wide temperature
range of – 40 ~ +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WT
Smaller
ZT
Smaller
Specifications
ZG
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 40 ~ +105°C
6.3 ~ 50V
0.1 ~ 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
6.3
0.38
10
0.32
Measurement frequency : 120Hz, Temperature : 20°C
16
25
35
50
0.20
0.16
0.14
0.14
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio
Z– 25°C / Z+20°C
6
5
3
3
3
3
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
10
10
6
6
4
4
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Capacitance
change
tan δ
Leakage current
Within ±25% of initial value (16V or less)
Within ±20% of initial value (25V or more)
300% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
Voltage mark for 6.3V is 6V .
4.5
+0.1
–0.2
0.5 ~ 0.8
Positive
(mm)
φD _{4 5 6.3}
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
Negative
Dimensions
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
4
19
5
26
5
32
6.3
52
10
1A
5
24
5
30
6.3
40
16
1C
4
16
5
26
6.3
35
6.3
44
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UZ T 1C 1 0 0 MC L 1GB
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
25
1E
4
11
5
20
6.3
33
6.3
42
35
1V
4
13
5
22
6.3
36
50
1H
4
0.9
4
2.2
4
2.8
4
3.3
4
5.4
4
9.6
4
12
5
16
6.3
26
Case size Rated
φ D (mm)
ripple
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are
given in page 25, 26.
Please select UX(p.74), UJ(p.76) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V