UZP1A100MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZP 4.5mmL Chip Type, Bi-Polarized
series
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WP
Smaller
ZP
Smaller
Specifications
ZE
Item
Performance Characteristics
Category Temperature Range – 40 ~ +85°C
Rated Voltage Range
Rated Capacitance Range
6.3 ~ 50V
0.1 ~ 47µF
Capacitance Tolerance
Leakage Current
tan δ
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
6.3
0.30
Measurement frequency : 120Hz, Temperature : 20°C
10
16
25
35
50
0.24
0.20
0.18
0.16
0.16
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
4
3
2
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C
8
8
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 2000 hours' application of rated voltage
at 85°C with the polarity inverted every 250
hours, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
300% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature,they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10µF)
Capacitance
Lot No.
Voltage
Plastic platform
0.3 MAX.
C±0.2
Voltage mark for 6.3V is 6V .
4.5
+0.1
–0.2
0.5 ~ 0.8
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UZ P 1 C 1 0 0 MCL 1GB
(mm)
φD 4 5 6.3
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
6.3
0J
5
28
6.3
37
6.3
45
10
1A
4
17
6.3
33
6.3
41
16
1C
4
12
5
23
6.3
37
6.3
49
25
1E
5
12
5
16
6.3
27
35
1V
4
8.4
5
16
5
18
6.3
29
50
1H
4
1.0
4
2.0
4
2.8
4
4.0
4
8.4
5
13
5
17
6.3
20
Case size
φ D (mm)
Rated
ripple
Rated Ripple (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please select WP(p.47), UN(p.77) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V