UZG1C100MCL1GB Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZG 3.95mmL MAX. Chip Type,
Wide Temperature Range
series
Chip type with 3.95mmLMAX height. Operating over wide
temperature range of – 40 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
ZT
Smaller
Specifications
ZG
Item
Performance Characteristics
Category Temperature Range – 40 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range 0.1 to 100µF
Capacitance Tolerance ± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
6.3
10
16
25
35
50
120Hz 20°C
0.38
0.32
0.20
0.16
0.14
0.14
Stability at Low
Temperature
Rated voltage (V)
6.3
10
16
25
35
50 120Hz
Impedance ratio ^{Z–25°C / Z+20°C}
6
5
3
3
3
3
ZT / Z20 (MAX.) _{Z–40°C / Z+20°C}
10
10
6
6
4
4
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 105°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to
soldering heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate and
restored to 20°C.
Black print on the case top.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Chip Type
Voltage (C : 16V)
Lot No.
Series
Plastic platform
0.3 MAX.
C±0.2
Capacitance
Voltage
V 6.3 10 16 25
Code j A C E
3.90
+0.05
–0.2
35 50
VH
0.5 to 0.8
Type numbering system (Example : 16V 10µF)
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
U ZG 1 C 1 0 0 MC L 1 GB
(mm)
φD 4 5 6.3
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Negative
Rated voltage (16V)
Series name
Type
Dimensions
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
4
19
5
26
5
32
6.3
52
10
1A
5
24
5
30
6.3
40
16
1C
4
16
5
26
6.3
35
6.3
44
25
1E
4
11
5
20
6.3
33
6.3
42
35
1V
4
13
5
22
6.3
36
50
1H
4
0.9
4
2.2
4
2.8
4
3.3
4
5.4
4
9.6
4
12.
5
16.
6.3
26.
Case size Rated
φ D (mm) ripple
Rated ripple current (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size soldering by reflow are given
in page 18,19.
Please refer to page 3 for the minimum order quantity.
CAT.8100C