UZG0J100MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZG 3.95mmL MAX. Chip Type,
Wide Temperature Range
series
Chip type with 3.95mmLMAX height. Operating over wide
temperature range of – 40 ~ +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
ZT
Smaller
ZG
Specifications
Item
Performance Characteristics
Category Temperature Range – 40 ~ +105°C
Rated Voltage Range
6.3 ~ 50V
Rated Capacitance Range 0.1 ~ 100µF
Capacitance Tolerance ± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
tan δ
Rated voltage (V)
tan δ (MAX.)
6.3
10
16
25
35
50
120Hz 20°C
0.38
0.32
0.20
0.16
0.14
0.14
Stability at Low
Temperature
Rated voltage (V)
6.3
10
16
25
35
50 120Hz
Impedance ratio ^{Z–25°C / Z+20°C}
6
5
3
3
3
3
ZT / Z20 (MAX.) _{Z–40°C / Z+20°C}
10
10
6
6
4
4
Endurance
After 1000 hours' application of rated voltage at 105°C,
capacitors meet the characteristic requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
300% or less of initial specified value
Initial specified value or less
Shelf Life
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
Resistance to
soldering heat
Marking
The capacitors shall be kept on the hot plate maintained at 250°C for 30
seconds. After removing from the hot plate and restored at room temperature,
they meet the characteristic requirements listed at right.
Black print on the case top.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Chip Type
Voltage (C : 16V)
Lot No.
Series
Plastic platform
0.3 MAX.
C±0.2
Capacitance
Voltage
V 6.3 10 16 25
Code j A C E
3.90
+0.05
–0.2
35 50
VH
0.5 ~ 0.8
Type numbering system (Example : 16V 10µF)
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
U ZG 1 C 1 0 0 MC L 1 GB
(mm)
φD 4 5 6.3
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Negative
Rated voltage (16V)
Series name
Type
Dimensions
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
4
19
5
26
5
32
6.3
52
10
1A
5
24
5
30
6.3
40
16
1C
4
16
5
26
6.3
35
6.3
44
25
1E
4
11
5
20
6.3
33
6.3
42
35
1V
4
13
5
22
6.3
36
50
1H
4
0.9
4
2.2
4
2.8
4
3.3
4
5.4
4
9.6
4
12.
5
16.
6.3
26.
Case size Rated
φ D (mm) ripple
Rated Ripple (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
Taping specifications are given in page 24.
Recommended land size are given in page 25.
Please contact us for the soldering by reflow.
Please refer to page 3 for the minimum order quantity.
CAT.8100V