UZE0J100MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZE 3.95mmL MAX. Chip Type, Bi-polarized
series
Chip type with 3.95mmL MAX, height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
ZP
Smaller
ZE
Specifications
Item
Performance Characteristics
Category Temperature Range
– 40 ~ +85°C
Rated Voltage Range
Rated Capacitance Range
6.3 ~ 50V
0.1 ~ 47µF
Capacitance Tolerance
Leakage Current
tan δ
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
6.3
0.30
Measurement frequency : 120Hz, Temperature : 20°C
10
16
25
35
50
0.24
0.20
0.18
0.16
0.16
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
4
3
2
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C
8
8
4
4
3
3
Eudurance
Shelf Life
Resistance to soldering
heat
After 1000 hours' application of rated voltage
at 85°C with the polarity inverted every 250
hours, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
300% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature,they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Marking
Black print on the case top.
Chip Type
Voltage (C : 16V)
Lot No.
Series
Plastic platform
0.3 MAX.
C±0.2
Capacitance
3.90
+0.05
–0.2
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
0.5 ~ 0.8
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
U Z E 1 C 1 0 0 MC L 1 GB
(mm)
φD 4 5 6.3
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
V
6.3
10
16
25
35
50
Cap. (µF)
Code
0J
1A
1C
1E
1V
1H
0.1
0R1
4
1.0
0.22
R22
4
2.0
0.33
R33
4
2.8
0.47
R47
4
4.0
1
010
4
8.4
2.2
2R2
4
8.4
5
13
3.3
3R3
5
12
5
16
5
17
4.7
4R7
4
12
5
16
5
18
6.3
20
10
100
4
17
5
23
6.3
27
6.3
29
22
220
5
28
6.3
33
6.3
37
33
330
6.3
37
6.3
41
6.3
49
47
470
6.3
45
Case size
φ D (mm)
Rated
ripple
Rated Ripple (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
Taping specifications are given in page 24.
Recommended land size are given in page 25.
Please contact us for the soldering by reflow.
Please refer to page 3 for the minimum order quantity.
CAT.8100V