UZD1C100MCL1GB Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
ZD 3.0mmL Chip Type
series
Chip type with 3.0mmL height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
ZR
Smaller
ZD
Specifications
Item
Performance Characteristics
Category Temperature Range – 40 to +85°C
Rated Voltage Range
4 to 25V
Rated Capacitance Range 2.2 to 100µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
4
6.3
10
16
25
120Hz 20°C
0.50
0.40
0.30
0.24
0.19
Stability at Low
Temperature
Rated voltage (V)
4
6.3
10
16
25
120Hz
Impedance ratio ^{Z–25°C / Z+20°C}
7
4
3
2
2
ZT / Z20 (MAX.) _{Z–40°C / Z+20°C}
15
8
8
4
4
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 85°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they shall meet the specified values for the endurance characteristics listed above.
Resistance to
soldering heat
Marking
The capacitors are kept on a hot plate for 30 seconds, which is maintained at
250°C. The capacitors shall meet the characteristic requirements listed at
right when they are removed from the plate and restored to 20°C.
Black print on the case top.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Chip Type
Voltage (C : 16V)
Lot No.
Series
Plastic platform
0.3 MAX.
C±0.2
Capacitance
Voltage
V
4 6.3 10 16
Code g j A C
3.0
+0.2
–0.1
25
E
0.5 to 0.8
Positive
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
U Z D 1 C 1 0 0 MC L 1 GB
(mm)
φD 4 5 6.3
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
Negative E 1.0 1.3 2.2
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
Cap. (µF)
2.2
3.3
4.7
5.6
6.8
10
22
33
47
100
V
Code
2R2
3R3
4R7
5R6
6R8
100
220
330
470
101
4
0G
4
20
5
28
5
33
6.3
56
6.3
0J
5
28
5
37
6.3
45
6.3
70
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz or more
1.50
10
1A
5
33
6.3
41
16
1C
5
23
6.3
37
25
1E
4
7
4
11
4
16
5
18
5
20
6.3
27
Case size _Rated
φ D (mm) _ripple
Rated ripple current (mArms) at 85°C 120Hz
Taping specifications are given in page 23.
Recommended land size soldering by reflow are given
in page 18,19.
Please refer to page 3 for the minimum order quantity.
CAT.8100C