UWZ0J330MCL1GB Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WZ Chip Type, Wide Temperature Range
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times
(φ8 × 6.2, φ10 × 10 : 1 time)
Chip type operating over wide temperature range of to – 55 to +105°C.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WZ
High
Temperature
Reflow
WT
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Performance Characteristics
– 55 to +105°C
6.3 to 50V
0.1 to 1500µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
6.3
0.30
10
0.24
16
0.20
Measurement frequency : 120Hz at 20°C
25
35
50
0.16
0.14
0.14
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio
Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
8
8
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be
met when the capacitors are restored to
20°C after the rated voltage is applied for
1000 hours at 105°C.
Capacitance
Within ±25% of the initial capacitance value for capacitors of 16V or less.
change
Within ±20% of the initial capacitance value for capacitors of 25V or more.
tan δ
200% or less than the initial specified value
Leakage current Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
Type numbering system (Example : 6.3V 33µF)
(φ4 to φ6.3 )
Voltage (C:16V)
Series
Plastic platform
0.3 MAX.
C±0.2
Positive
Lot No.
Capacitance
(φ8 × 6.2 )
Voltage ( J:6.3V)
Trade mark
Series
L
+0.1
–0.2
(L±0.3) 1
H
1 Apply to φ6.3 × 5.8, φ6.3 × 7.7
Plastic platform
0.3 MAX.
C±0.2
Negative
Positive
Lot No. Capacitance
(φ8 × 10, φ10×10)
Voltage (E:25V)
Trade mark
Series
L±0.3
Plastic platform
0.3 MAX.
H
C±0.2
Negative
Positive
Lot No. Capacitance
L±0.5
Dimension table in next page.
Negative
H
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWZ 0 J 3 3 0 M C L 1G B
φD
4 to 6.3 (5.4L)
6.3 to 10 (L 5.8L)
code
GB
GS
Package code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (33µF)
Rated voltage (6.3V)
Series name
Type
φD × L
4 × 5.4
5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2
8 × 10
(mm)
10 × 10
A
1.8
2.1
2.4
2.4
2.4
3.3
2.9
3.2
B
4.3
5.3
6.6
6.6
6.6
8.3
8.3 10.3
C
4.3
5.3
6.6
6.6
6.6
8.3
8.3 10.3
E
1.0
1.3
2.2
2.2
2.2
2.3
3.1
4.5
L
5.4
5.4
5.4
5.4
7.7
6.2
10
10
H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
CAT.8100C