UWZ0J220MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WZ Chip Type, Wide Temperature Range
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times
(φ8 × 6.2, φ10 × 10 : 1 time)
Chip type operating over wide temperature range of to – 55 ~ +105°C.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WZ
High
Temperature
Reflow
WT
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 55 ~ +105°C
6.3 ~ 50V
0.1 ~ 1500µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
6.3
0.30
10
0.24
16
0.20
25
0.16
35
0.14
50
0.14
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio
Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
8
8
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Capacitance
change
tan δ
Leakage current
Within ±25% of initial value for capacitors of 16V or less.
Within ±20% of initial value for capacitors of 25V or more.
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(f4 ~ 6.3 )
Voltage (C:16V)
Positive
Plastic platform
Series
0.3 MAX.
C±0.2
Lot No.
(f8 ´ 6.2 )
Voltage ( A:10V)
Trade mark
Capacitance
L ^+Ð00..21
(L±0.3) 1
H
1 Apply to f6.3 ´ 5.8, f6.3 ´ 7.7
Plastic platform
Series
0.3 MAX.
C±0.2
Negative
Positive
Lot No. Capacitance
L±0.3
H
Negative
(f8 ´ 10, f10´10)
Positive
Voltage (V:35V)
Trade mark
Plastic platform
Series
0.3 MAX.
C±0.2
Lot No. Capacitance
L±0.5
Dimension table in next page.
H
Negative
Type numbering system (Example : 6.3V 33µF)
U¹ W² Z³ 0⁴ J⁵ 3⁶ 3⁷ 0⁸ M⁹ C^{10 1}L^{1 1}1² G¹³ B¹⁴
fD code
4 ~ 6.3 (5.4L) GB
6.3 ~ 10 (L 5.8L) GS
Package code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (33mF)
Rated voltage (6.3V)
Series name
Type
(mm)
fD ´ L _{4 ´ 5.4 5 ´ 5.4 6.3 ´ 5.4 6.3 ´ 5.8 6.3 ´ 7.7 8 ´ 6.2 8 ´ 10 10 ´ 10}
A 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2
B 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3
C 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3
E 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5
L 5.4 5.4 5.4 5.4 7.7 6.2 10 10
H 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
CAT.8100V