UWS1A101MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WS Chip Type, High CV
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times
(φ8 × 6.2, φ10 × 10 : 1 time)
Chip type higher capacitance in large case size.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WS
High
Temperature
Reflow
UR
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Performance Characteristics
– 40 to +85°C
6.3 to 50V
22 to 1500µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) .
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.)
0.28
0.24
0.20
0.16
0.14
0.12
Measurement frequency: 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio Z– 25°C / Z+20°C
5
4
3
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C 10
8
6
4
3
3
Endurance
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ6.3, φ8 × 6.2)
Voltage (A:10V) _Series
Plastic platform
0.3MAX.
1
Trade mark
Lot No. Capacitance
1 Size φ8 × 6.2 only
L ±0.3
C±0.2
Positive
Negative
H
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWS 1 A 1 0 1 M C L 1G S
Package code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (10V)
Series name
Type
(φ8 × 10, φ10 × 10)
Voltage (V:35V) _Series
Plastic platform
0.3MAX.
C±0.2
Positive
Trade mark
Lot No. Capacitance
L±0.5
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimension table in next page.
Negative
H
φ D × L _{6.3 × 5.8}
A
2.4
B
6.6
C
6.6
E
2.2
L
5.8
H
0.5 to 0.8
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 to 0.8
8 × 6.2
3.3
8.3
8.3
2.3
6.2
0.5 to 0.8
8 × 10
2.9
8.3
8.3
3.1
10
0.8 to 1.1
(mm)
10 × 10
3.2
10.3
10.3
4.5
10
0.8 to 1.1
CAT.8100C