UWS0J221MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WS Chip Type, High CV
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times
(φ8 × 6.2, φ10 × 10 : 1 time)
Chip type higher capacitance in large case size.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WS
High
Temperature
Reflow
UR
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
– 40 ~ +85°C
6.3 ~ 50V
22 ~ 1500µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) .
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.)
0.28
0.24
0.20
0.16
0.14
0.12
Measurement frequency: 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
5
4
3
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C 10
8
6
4
3
3
Endurance
After 2000 hours' application of rated voltage
at 85°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C,
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Black print on the case top.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Chip Type
(φ6.3, φ8 × 6.2)
Voltage (A:10V) _Series
Plastic platform
0.3MAX.
1
Trade mark
Lot No. Capacitance
1 Size φ8 × 6.2 only
L ±0.3
C±0.2
H
(φ8 × 10, φ10 × 10)
Voltage (V:35V) _Series
Plastic platform
0.3MAX.
C±0.2
Trade mark
Lot No. Capacitance
L±0.5
H
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimension table in next page.
Positive
Negative
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWS 1 A 1 0 1 M C L 1G S
Package code
Configuration
Capacitance tolerance (–20%)
Rated Capacitance (100µF)
Rated voltage (10V)
Series name
Type
Positive
φD×L
A
B
C
E
L
H
6.3 × 5.8
2.4
6.6
6.6
2.2
5.8
0.5 ~ 0.8
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 ~ 0.8
8 × 6.2
3.3
8.3
8.3
2.3
6.2
0.5 ~ 0.8
8 × 10
2.9
8.3
8.3
3.1
10
0.8 ~ 1.1
(mm)
10 × 10
3.2
10.3
10.3
4.5
10
0.8 ~ 1.1
Negative
CAT.8100V