UWP1C100MCL1GB Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WP 5.5mmL Chip Type, Bi-Polarized
series
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WP
Smaller
Specifications
ZP
Item
Performance Characteristics
Category Temperature Range – 40 to +85°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range 0.1 to 100µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater.
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
6.3
0.24
10
0.20
16
0.17
Measurement frequency : 120Hz at 20°C
25
35
50
0.17
0.15
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio}
Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
8
6
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be met
when the capacitors are restored to 20°C after the
rated voltage is applied for 1000 hours at 85°C
with the polarity inverted every 250 hours.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which
is maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10µF)
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWP 1 C 1 0 0 M C L 1 G B
Voltage mark for 6.3V is 6V .
5.4
+0.1
–0.2
Dimensions
0.5 to 0.8
(mm)
φD _{4 5 6.3 8}
A 1.8 2.1 2.4 3.3
B 4.3 5.3 6.6 8.3
C 4.3 5.3 6.6 8.3
E 1.0 1.3 2.2 2.3
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
5
28
6.3
37
6.3
45
8
82
10
1A
4
17
6.3
33
6.3
41
8
61
16
1C
4
5
6.3
6.3
8
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz or more
1.50
25
35
50
1E
1V
1H
4
1.0
4
2.0
4
2.8
4
4.0
4
8.4
4
8.4
5
13
5
12
5
16
5
17
12
5
16
5
18
6.3
20
23
6.3
27
6.3
29
8
36
37
8
50
8
54
49
8
75
61
Allowable
Case size
φ D (mm)
R^ria^pt^ped^le
ripple
Rated ripple current (mArms) at 85°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UN(p.166) series if high C/V products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100C