UWP0J220MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WP 5.5mmL Chip Type, Bi-Polarized
series
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WP
Smaller
Specifications
ZP
Item
Performance Characteristics
Category Temperature Range – 40 ~ +85°C
Rated Voltage Range
6.3 ~ 50V
Rated Capacitance Range 0.1 ~ 100µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
tan δ
After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
6.3
0.24
10
0.20
16
0.17
25
0.17
35
0.15
50
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio}
Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
8
6
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 1000 hours' application of rated voltage
at 85°C with the polarity inverted every 250
hours, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10µF)
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWP 1 C 1 0 0 M C L 1 G B
Taping code
Configuration
Voltage mark for 6.3V is 6V .
5.4
+0.1
–0.2
Dimensions
0.5 ~ 0.8
(mm)
φD _{4 5 6.3 8}
A 1.8 2.1 2.4 3.3
B 4.3 5.3 6.6 8.3
C 4.3 5.3 6.6 8.3
E 1.0 1.3 2.2 2.3
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
6.3
0J
5
28
6.3
37
6.3
45
8
82
10
1A
4
6.3
6.3
8
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
17
33
41
61
10 kHz~
1.50
16
1C
4
5
6.3
6.3
8
25
35
50
1E
1V
1H
4
1.0
4
2.0
4
2.8
4
4.0
4
8.4
4
8.4
5
13
5
12
5
16
5
17
12
5
16
5
18
6.3
20
23
6.3
27
6.3
29
8
36
37
8
50
8
54
49
8
61
75
Case size
φ D (mm)
Allowable
R^ria^pte^pd^le
ripple
Rated Ripple (mArms) at 85°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please select UN(p.77) series if high C/V products are
reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V