UWJ0J220MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WJ 5.5mmL Chip Type
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec.
2 times
Chip type with 5.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Load life of 2000 hours at 85°C
Adapted to the RoHS directive (2002/95/EC).
WJ
High
Temperature
Reflow
WX
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 40 ~ +85°C
6.3 ~ 50V
0.1 ~ 150µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater.
Rated voltage (V)
tan δ (MAX.)
6.3
0.26
Measurement frequency : 120Hz, Temperature : 20°C
10
16
25
35
50
0.20
0.16
0.14
0.12
0.12
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C
8
8
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 2000 hours' application of rated voltage
at 85°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage Current
Within ±20% of initial value
200% or less of initial specified value
Initial specifed value or less
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
Voltage (A:10V) Series
Plastic platform
0.3 MAX.
C±0.2
Positive
Lot No. Capacitance
5.4
+0.1
–0.2
0.5 ~ 0.8
Negative
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UW J 1 C 1 0 0 MC L 1 G B
Package code
Configuration
Capacitance toleranc (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
φD
4
(mm)
5
6.3
A
1.8
2.1
2.4
B
4.3
5.3
6.6
C
4.3
5.3
6.6
E
1.0
1.3
2.2
Dimension table in next page.
CAT.8100V