UWH1A101MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WH Chip Type, High Reliability
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times
(φ8 × 6.2, φ10 × 10 : 1 time)
Chip type high temperature range, for +125°C use.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WH
High
Temperature
Reflow
UB
Specifications
Item
Category Temperature Range
Rated Voltage Range
– 40 to +125°C
10 to 50V
Performance Characteristics
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
10 to 330µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
10
0.32
16
0.24
Measurement frequency : 120Hz at 20°C
25
35
50
0.21
0.18
0.18
Rated voltage (V)
10
Stability at Low Temperature
Impedance ratio _{Z– 40°C / Z+20°C}
ZT / Z20 (MAX.)
12
Measurement frequency : 120Hz
16
25
35
50
8
6
4
4
Endurance
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 1000 hours at 125°C.
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ8 × 6.2)
Voltage (A:10V) Series
Plastic platform
0.3MAX.
Trade mark
Lot No. Capacitance
L±0.3
C±0.2
Positive
Negative
H
(φ8 × 10, φ10 × 10)
Voltage (V:35V) Series
Plastic platform
0.3MAX.
Trade mark
Lot No. Capacitance
L±0.5
Voltage
V
10 16 25 35 50
Code A C E V H
C±0.2
Positive
Negative
H
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWH 1 A 1 0 1 M C L 1 G S
Package code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (10V)
Series name
Type
φD × L
A
B
C
E
L
H
8 × 6.2
3.3
8.3
8.3
2.3
6.2
0.5 to 0.8
8 × 10
2.9
8.3
8.3
3.1
10
0.8 to 1.1
(mm)
10 × 10
3.2
10.3
10.3
4.5
10
0.8 to 1.1
Dimension table in next page.
CAT.8100C