UWH1A101MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WH Chip Type, High Reliability
High Temperature (260°C) Reflow
series
Corresponding with 260°C peak reflow soldering
Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times
(φ8 × 6.2, φ10 × 10 : 1 time)
Chip type high temperature range, for +125°C use.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WH
High
Temperature
Reflow
UB
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Performance Characteristics
– 40 ~ +125°C
10 ~ 50V
10 ~ 330µF
± 20% at 120Hz, 20°C
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
10
0.32
16
0.24
25
0.21
35
0.18
50
0.18
Rated voltage (V)
10
Stability at Low Temperature
Impedance ratio _{Z– 40°C / Z+20°C}
ZT / Z20 (MAX.)
12
Measurement frequency : 120Hz
16
25
35
50
8
6
4
4
Endurance
After 1000 hours' application of rated voltage at
125°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±30% of initial value
300% or less of intial specified value
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(φ8 × 6.2)
Plastic platform
Positive
Voltage (A:10V) Series
0.3MAX.
C±0.2
Trade mark
L±0.3
Lot No. Capacitance
H
Negative
(φ8 × 10, φ10 × 10)
Voltage (V:35V) Series
Plastic platform
Positive
0.3MAX.
C±0.2
Trade mark
L±0.5
Lot No. Capacitance
Voltage
V
10 16 25 35 50
Code A C E V H
H
Negative
Type numbering system (Example : 10V 100µF)
U¹ W² H³ 1⁴ A⁵ 1⁶ 0⁷ 1⁸ M^{9 1}C⁰ L^{11 1}1² G¹³ S¹⁴
Package code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (100mF)
Rated voltage (10V)
Series name
Type
(mm)
fD´L _{8 ´ 6.2}
8 ´ 10
10 ´ 10
A
3.3
2.9
3.2
B
8.3
8.3
10.3
C
8.3
8.3
10.3
E
2.3
3.1
4.5
L
6.2
10
10
H
0.5 ~ 0.8
0.8 ~ 1.1
0.8 ~ 1.1
Dimension table in next page.
CAT.8100V