UWG1A101MCL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WG Chip Type, Low Impedance
series
Chip type, operating over wide temperature range of to – 55 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
UD
Low
Impedance
WG
Low
Impedance
WF
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range 1 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
Tangent of loss angle (tan δ)
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
6.3
0.26
10
0.19
16
0.16
25
0.14
35
0.12
50
0.12
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio}
Z– 25°C / Z+20°C
2
2
2
2
2
2
ZT / Z20 (MAX.)
Z– 55°C / Z+20°C
4
4
3
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
The specifications listed at right shall be met
when the capacitors are restored to 20°C
after the rated voltage is applied for 1000
hours at 105°C.
Capacitance change Within ±20% of the initial capacitance value
tan δ
200% or less than the initial specified value
Leakage current
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Marking
Black print on the case top.
Chip Type
(φ4 to φ6.3)
Capacitance
105°C Marking
Voltage
Plastic platform
0.3 MAX.
C±0.2
Positive
Lot No.
(φ8 × 6.2 )
Capacitance
105°C Marking
Trade mark
L
+0.1
-0.2
Voltage
Plastic platform
0.3 MAX.
H
C±0.2
Negative
Positive
Type numbering system (Example : 10V 100µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWG 1 A 1 0 1 MC L 1 G S
Taping code
φD code
4 to 6.3 GB
8 • 10 GS
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (10V)
Configuration
φD
code
4 to 6.3 CL
8 (6.2L) CL
8 (10L) • 10 NL
Series name
Type
Lot No.
(φ8 × 10, φ10 × 10 )
Capacitance
105°C Marking
Trade mark
Voltage
L±0.3
Plastic platform
0.3 MAX.
Lot No.
Voltage mark for 6.3V is 6V .
L±0.5
Pressure relief vent
Dimension table in next page.
H
C±0.2
Negative
Positive
(mm)
φD × L _{4 × 5.4 5 × 5.4 6.3 × 5.4 8 × 6.2 8 × 10 10 × 10}
A
1.8
2.1
2.4
3.3
2.9
3.2
B
4.3
5.3
6.6
8.3
8.3
10.3
C
4.3
5.3
6.6
8.3
8.3
10.3
E
1.0
1.3
2.2
2.3
3.1
4.5
L
5.4
5.4
5.4
6.2
10
10
H
0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
H
Negative
CAT.8100C