UWG0J220MCL Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WG Chip Type, Low Impedance
series
Chip type, operating over wide temperature range of to – 55 ~ +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
UD
Low
Impedance
WG
Low
Impedance
WF
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 55 ~ +105°C
6.3 ~ 50V
1 ~ 1500µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
6.3
0.26
10
0.19
Measurement frequency : 120Hz, Temperature : 20°C
16
25
35
50
0.16
0.14
0.12
0.12
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio
Z– 25°C / Z+20°C
2
2
2
2
2
2
ZT / Z20 (MAX.)
Z– 55°C / Z+20°C
4
4
3
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change Within ±20% of initial value
tan δ
200% or less of initial specified value
Leakage current
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(f4 ~ 6.3)
Capacitance
Voltage
105¡C Marking
Plastic platform
0.3 MAX.
Positive
C±0.2
Lot No.
(f8 ´ 6.2 )
Capacitance
105¡C Marking
Trade mark
L ^+-00..21
H
Negative
Plastic platform
Voltage
0.3 MAX.
Positive
C±0.2
Type numbering system (Example : 10V 100µF)
U¹ W² G³ 1⁴ A⁵ 1⁶ 0⁷ 1⁸ M⁹ C^{10 1}L^{1 1}1² G^{13 1}S⁴
Taping code
4 ~^fD6.3
code
GB
8 ¥ 10 GS
Configuration
Capacitance tolerance (±20%) _{4 ~}^{fD6.3 cCodLe}
Rated Capacitance (100µF)
Rated voltage (10V)
8 (6.2L)
8 (10L) ¥ 10
CNLL
Series name
Type
Lot No.
(f8 ´ 10, f10 ´ 10 )
Capacitance
105¡C Marking
Voltage
Trade mark
L±0.3
Plastic platform
0.3 MAX.
Lot No.
L±0.5
Voltage mark for 6.3V is 6V . ^{Pressure relief vent}
Dimension table in next page.
H
Negative
Positive
C±0.2
(mm)
fD ´ L _{4 ´ 5.4 5 ´ 5.4 6.3 ´ 5.4 8 ´ 6.2 8 ´ 10 10 ´ 10}
CHABEL
0.514415~.....833040.8 0.525515~.....133340.8 0.526625~.....466240.8 0.538826~.....333320.8 0.828831~....093311.1 0.81134100~..025..331.1
H
Negative
CAT.8100V