UWF1C470MCL1GB Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WF Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Specifications
WG
Low
Impedance
WF
Low
Impedance
WT
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Performance Characteristics
– 55 to +105°C
6.3 to 35V
1 to 220µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Rated voltage (V)
tan δ ( MAX.)
6.3
0.22
10
0.19
Measurement frequency : 120Hz at 20°C
16
25
35
0.16
0.14
0.12
Rated voltage (V)
6.3
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
2
ZT / Z20 (MAX.) Z– 55°C / Z+20°C
4
Measurement frequency : 120Hz
10
16
25
35
2
2
2
2
4
3
3
3
Endurance
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 1000 hours at 105°C.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are removed
from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ4 to φ6.3)
105˚C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
Positive
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWF 1 C 1 0 0 MC L 1 G B
φD Code
4 to 6.3 GB
8
GS
Taping code
Configuration
(φ8)
105˚C Marking
Capacitance
Trade mark
Lot No.
5.4
+0.1
-0.2
0.5 to 0.8
Plastic platform
Voltage
0.3 MAX.
C±0.2
Negative
Positive
(mm)
φD _{4 5 6.3 8}
A 1.8 2.1 2.4 3.3
B 4.3 5.3 6.6 8.3
C 4.3 5.3 6.6 8.3
E 1.0 1.3 2.2 2.3
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
6.2±0.3
Dimensions
V
Cap. (µF)
Code
1
010
1.5
1R5
2.2
2R2
3.3
3R3
4.7
4R7
6.8
6R8
10
100
15
150
22
220
4
33
330
5
47
470
5
68
680
6.3
100
101
6.3
150
151
8
220
221
8
0.5 to 0.8
6.3
0J
5.0
50
2.6
80
2.6
80
1.3 115
1.3 115
0.8 150
0.8 150
Negative
5
5
6.3
6.3
8
8
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.35
0.50
0.64
0.83
Voltage mark for 6.3V is 6V.
10
1A
2.6
80
2.6
80
1.3 115
1.3 115
0.8 150
0.8 150
10 kHz or more
1.00
16
25
35
1C
1E
1V
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
5
2.6
80
4
5.0
50
5
2.6
80
5
2.6
80
5
2.6
80
6.3
1.3 115
6.3
1.3 115
5
2.6
80
6.3
1.3 115
6.3
1.3 115
6.3
1.3 115
6.3
1.3 115
8
0.8 150
6.3
1.3 115
8
0.8 150
8
0.8 150
8
0.8 150
8
0.8 150
8
0.8 150
Case size
φ D (mm)
Impedance
Rated
ripple
Max. Impedance (Ω) at 20°C 100kHz
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UJ(p.164) series if high C/V products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100C