UWF0J220MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
WF Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Specifications
WG
Low
Impedance
WF
Low
Impedance
WT
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Performance Characteristics
– 55 ~ +105°C
6.3 ~ 35V
1 ~ 220µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Rated voltage (V)
tan δ ( MAX.)
6.3
0.22
Measurement frequency : 120Hz, Temperature : 20°C
10
16
25
35
0.19
0.16
0.14
0.12
Rated voltage (V)
6.3
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
2
ZT / Z20 (MAX.) Z– 55°C / Z+20°C
4
Measurement frequency : 120Hz
10
16
25
35
2
2
2
2
4
3
3
3
Endurance
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C,
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements listed
at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
(φ4 ~ 6.3)
105˚C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
Positive
(φ8)
105˚C Marking
Capacitance
Trade mark
Lot No.
5.4
+0.1
-0.2
0.5 ~ 0.8
Plastic platform
Voltage
0.3 MAX.
C±0.2
Negative
Positive
(mm)
φD _{4 5 6.3 8}
A 1.8 2.1 2.4 3.3
B 4.3 5.3 6.6 8.3
C 4.3 5.3 6.6 8.3
E 1.0 1.3 2.2 2.3
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UWF 1 C 1 0 0 MC L 1 G B
φD Code
4 ~ 6.3 GB
8
GS
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
6.2±0.3
Dimensions
V
Cap. (µF)
Code
1
010
1.5
1R5
2.2
2R2
3.3
3R3
4.7
4R7
6.8
6R8
10
100
15
150
22
220
4
33
330
5
47
470
5
68
680
6.3
100
101
6.3
150
151
8
220
221
8
0.5 ~ 0.8
6.3
0J
Negative
5.0
50
5
2.6
80
5
2.6
80
6.3
1.3 115
6.3
1.3 115
8
0.8 150
8
0.8 150
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.35
0.50
0.64
0.83
Voltage mark for 6.3V is 6V.
10
1A
2.6
80
2.6
80
1.3 115
1.3 115
0.8 150
0.8 150
10 kHz~
1.00
16
25
35
1C
1E
1V
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
4
5.0
50
5
2.6
80
4
5.0
50
5
2.6
80
5
2.6
80
5
2.6
80
6.3
1.3 115
6.3
1.3 115
5
2.6
80
6.3
1.3 115
6.3
1.3 115
6.3
1.3 115
6.3
1.3 115
8
0.8 150
6.3
1.3 115
8
0.8 150
8
0.8 150
8
0.8 150
8
0.8 150
8
0.8 150
Case size
φ D (mm)
Impedance
Rated
ripple
Max. Impedance (Ω) at 20°C 100kHz
Rated Ripple (mArms) at 105°C 100kHz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25, 26.
Please select UJ(p.76) series if high C/V products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V