UUX1E101MNL1GS Datasheet, PDF (1/2 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UX Chip Type, Higher Capacitance Range
series
Chip type, higher capacitance in larger case sizes..
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
UB
LR
High
Te m p e r a t u re
High
Voltage
UJ
Extended
range
UX
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
– 55 to +105°C (6.3 to 100V), – 40 to +105°C (160 to 400V)
6.3 to 400V
1 to 1000µF
± 20% at 120Hz, 20°C
Rated voltage (V)
Leakage Current
6.3 to 100
160 to 400
After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA). I = 0.04CV+100 ( µA) max.(1 minute's)
Measurement frequency : 120Hz at 20°C
Rated voltage (V) 6.3
tan δ (MAX.) 0.22
10
0.19
16
0.16
25
0.14
35
0.12
50
0.10
63
0.10
100
0.08
160
0.20
200
0.20
250
0.20
400
0.25
Measurement frequency: 120Hz
Rated voltage (V)
6.3 10
16
25
35
50
63 100 160 200 250 400
Stability at Low Temperature _{Impedance ratio Z– 55°C / Z+20°C 4}
4
3
3
3
2
3
4
—
—
—
—
ZT / Z20 (MAX.) Z– 40°C / Z+20°C —
—
—
—
—
—
—
—
6
6
6
10
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours (160 to 400V : 3000hours) at 105°C.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the intial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
(φ6.3, φ8 × 6.2)
105°C Marking
2 Voltage
1
Trade mark
Lot No. Capacitance
1 Size φ8 × 6.2 only
2 Voltage mark for 6.3V is 6V .
Plastic platform
0.3MAX.
L±0.3
(φ8 × 10, φ10 × 10)
105°C Marking
2 Voltage
Plastic platform
0.3MAX.
Trade mark
Lot No. Capacitance
L±0.5
Pressure relief vent
Dimension table in next page.
Type numbering system (Example : 10V 100µF)
C±0.2
Positive
Negative
H
C±0.2
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUX 1 A 1 0 1 M CL 1GS
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (10V)
Series name
Type
Package code
Size code
Configuration
D×L
6.3 × 7.7
8 × 6.2
8 × 10
10 × 10
Code
CL
CL
NL
NL
(mm)
φ D × L _{6.3 × 7.7 8 × 6.2 8 × 10 10 × 10}
A
2.4
3.3
2.9
3.2
B
6.6
8.3
8.3
10.3
C
6.6
8.3
8.3
10.3
E
2.2
2.3
3.1
4.5
L
7.7
6.2
10
10
H 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Negative
H
CAT.8100C