UUT1C100MCLGS Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UT 6mmL Chip Type , Wide Temperature Range
series
Chip type with load life 2000 hours at +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Specifications
UA Long Life
UX Higher C/V
UT
Long Life WT
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
4 to 50V
Rated Capacitance Range 0.1 to 100µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
Tangent of loss angle (tan δ)
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency :120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
4
0.37
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.13
50
0.12
Measurement frequency :120Hz
Rated voltage (V)
4
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio Z– 25°C / Z+20°C}
6
3
3
2
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C 12
8
5
4
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 2000 hours at
105°C.
Capacitance
change
tan δ
Leakage current
Within ±25% of the initial capacitance value (16V or less)
Within ±20% of the initial capacitance value (25V or more)
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3MAX.
C±0.2
Voltage mark for 6.3V is 6V .
5.8±0.3
0.5 to 0.8
Type numbering system (Example : 16V 10µF)
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUT 1C 1 0 0 MCL1GS
φD ₄
A 1.8
B 4.3
C 4.3
E 1.0
(mm)
5 6.3
2.1 2.4
5.3 6.6
5.3 6.6
1.3 2.2
Negative
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
Cap.(µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
0G
4
22
5
30
5
36
6.3
60
6.3
0J
4
22
5
30
5
36
6.3
60
10
1A
5
27
5
35
6.3
46
6.3
60
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more
Coefficient
0.70
1.00
1.17
1.36
1.50
16
1C
4
18
5
30
6.3
40
6.3
50
25
1E
4
5
6.3
6.3
35
50
1V
1H
4
1.0
4
2.6
4
3.2
4
3.8
4
6.2
4
11
4
14
13
4
15
5
19
23
5
25
6.3
30
38
6.3
42
48
AllRoawtaebdle
Case size
φ D (mm)
rip^rp^ipl^pe^le
Rated ripple current (mArms) at 105°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UX(p.158), UJ(p.164) series if high C/V products are
required.
Please refer to page 3 for the minimum order quantity.
CAT.8100C