UUT0G220MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UT 6mmL Chip Type , Wide Temperature Range
series
Chip type with load life 2000 hours at +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Specifications
UA Long Life
UX Higher C/V
UT
Long Life WT
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Performance Characteristics
– 55 ~ +105°C
4 ~ 50V
0.1 ~ 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Rated voltage (V)
tan δ (MAX.)
4
0.37
6.3
0.28
Measurement frequency :120Hz, Temperature : 20°C
10
16
25
35
50
0.24
0.20
0.16
0.13
0.12
Measurement frequency :120Hz
Rated voltage (V)
4
6.3
10
16
25
35
50
Impedance ratio Z– 25°C / Z+20°C
6
3
3
2
2
2
2
ZT / Z20 (MAX.) Z– 40°C / Z+20°C 12
8
5
4
3
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 2000 hours' application of rated voltage
at 105°C , capacitors meet the characteristic
requirements listed at right.
Capacitance
change
tan δ
Leakage current
Within ±25% of initial value (16V or less)
Within ±20% of initial value (25V or more)
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3MAX.
C±0.2
Voltage mark for 6.3V is 6V .
L±0.3
0.5 ~ 0.8
Type numbering system (Example : 16V 10µF)
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUT 1C 1 0 0 MCL1GS
Negative
φD ₄
A 1.8
B 4.3
C 4.3
E 1.0
L 5.8
(mm)
5 6.3
2.1 2.4
5.3 6.6
5.3 6.6
1.3 2.2
5.8 5.8
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
Cap.(µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
0G
4
22
5
30
5
36
6.3
60
6.3
0J
4
22
5
30
5
36
6.3
60
10
1A
5
27
5
35
6.3
46
6.3
60
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz~
1.50
16
1C
4
18
5
30
6.3
40
6.3
50
25
1E
4
13
5
23
6.3
38
6.3
48
35
1V
4
15
5
25
6.3
42
50
1H
4
1.0
4
2.6
4
3.2
4
3.8
4
6.2
4
11
4
14
5
19
6.3
30
AllRoawtaebdle
Case size
φ D (mm)
rip^rp^ipl^pe^le
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25, 26.
Please select UX(p.74), UJ(p.76) series if high C/V products are
required.
Please refer to page 3 for the minimum order quantity.
CAT.8100V