UUP1C100MCL1GS Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UP 6mmL Chip Type, Bi-Polarized
series
Chip type, bi-polarized withstanding high temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
UN
Extended
range
UP
Specifications
High
Te m p e r a t u re
WP
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range 0.1 to 47µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater.
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
6.3
0.24
10
0.20
16
0.17
Measurement frequency : 120Hz at 20°C
25
35
50
0.17
0.15
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio}
Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
8
6
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 1000 hours at
105°C with the polarity every 250 hours.
Capacitance change
tan δ
Leakage current
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Capacitance change
tan δ
Leakage current
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Black print on the case top.
Chip Type
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
5.8±0.3
Voltage mark for 6.3V is 6V
0.5 to 0.8
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUP 1C 1 0 0 MCL1GS
(mm)
φD _{4 5 6.3}
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
Taping code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
V
6.3
10
16
25
35
50
Cap.(µF)
Code
0J
1A
1C
1E
1V
1H
0.1
0R1
4
1.0
0.22
R22
4
2.0
0.33
R33
4
2.8
0.47
R47
4
4.0
1
010
4
8.4
2.2
2R2
4
8.4
5
13
3.3
3R3
5
12
5
16
5
17
4.7
4R7
4
12
5
16
5
18
6.3
20
10
100
4
17
5
23
6.3
27
6.3
29
22
220
5
28
6.3
33
6.3
37
33
330
6.3
37
6.3
41
6.3
49
47
470
6.3
45
Case size
φ D (mm)
Rated
ripple
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
10 kHz or more
1.50
Rated ripple current (mArms) at 105°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UN(p.166) series if high CV products are required.
Please refer to page 3 for the minimum order quantity.
CAT.8100C