UUP0J100MCL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UP 6mmL Chip Type, Bi-Polarized
series
Chip type, bi-polarized withstanding high temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
UN
Extended
range
UP
Specifications
High
Te m p e r a t u re
WP
Item
Performance Characteristics
Category Temperature Range – 55 ~ +105°C
Rated Voltage Range
6.3 ~ 50V
Rated Capacitance Range 0.1 ~ 47µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
tan δ
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
tan δ (MAX.)
6.3
0.24
10
0.20
16
0.17
25
0.17
35
0.15
50
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
10
16
25
35
50
Stability at Low Temperature _{Impedance ratio}
Z– 25°C / Z+20°C
4
3
2
2
2
2
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
8
6
4
4
3
3
Endurance
Shelf Life
Resistance to soldering
heat
Marking
After 1000 hours' application of rated
voltage at 105°C with the polarity inverted
every 250 hours, capacitors meet the
characteristic requirements listed at right.
Capacitance change
tan δ
Leakage current
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Leakage current
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Black print on the case top.
Chip Type
105°C Marking
Capacitance
Lot No.
Plastic platform
Voltage
0.3 MAX.
C±0.2
L±0.3
Voltage mark for 6.3V is 6V
0.5 ~ 0.8
Type numbering system (Example : 16V 10µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUP 1C 1 0 0 MCL1GS
(mm)
φD _{4 5 6.3}
A 1.8 2.1 2.4
B 4.3 5.3 6.6
C 4.3 5.3 6.6
E 1.0 1.3 2.2
L 5.8 5.8 5.8
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
Dimensions
Cap.(µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
V
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
6.3
0J
5
28
6.3
37
6.3
45
10
1A
4
6.3
6.3
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz
Coefficient
0.70
1.00
1.17
1.36
17
33
41
10 kHz~
1.50
16
1C
4
5
6.3
6.3
25
35
50
1E
1V
1H
4
1.0
4
2.0
4
2.8
4
4.0
4
8.4
4
8.4
5
13
5
12
5
16
5
17
12
5
16
5
18
6.3
20
23
6.3
27
6.3
29
37
49
Rated
Case size
φ D (mm)
ripple
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25, 26.
Please select UN(p.77) series if high CV products are required.
Please refer to page 3 for the minimum order quantity.
CAT.8100V