UUN0J331MNL Datasheet, PDF (1/1 Pages) Nichicon corporation – ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS
UN Chip Type, Bi-Polarized, Higher Capacitance Range
series
Chip Type ,higher capacitance in larger case sizes (φ12.5, φ16, φ18, φ20)
Designed for surface mounting on high density PC board.
Bi-polarized series for operations over wide temperature range of – 55 ~ +105°C.
Applicable to automatic mounting machine using carrier tape and tray.
Adapted to the RoHS directive (2002/95/EC).
UN
Bi-polarized _UJ
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 ~ +105°C
Rated Voltage Range
6.3 ~ 100V
Rated Capacitance Range 22 ~ 3300µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 1 minutes' application of rated voltage, leakage current is not more than 0.03CV or 4 (µA), whichever is greater.
Rated voltage (V)
6.3
10
16
25
35
50
63
100
120Hz 20°C
tan δ
tan δ (MAX)
0.26 0.22 0.18 0.16 0.14 0.12 0.10 0.09
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.
Rated voltage (V)
6.3
10
16
25
35
50
63
100
120Hz
Stability at Low Temperature _{Impedance ratio} Z–25°C / Z+20°C 5
4
3
2
2
2
2
2
ZT / Z20 (MAX.) _{Z–40°C / Z+20°C 10}
8
6
4
3
3
3
3
Endurance
After 2000 hours' application of rated voltage at 105°C with the
polarity inverted every 250 hours, capacitors meet the characteristic
requirements listed at right.
Capacitance change Within ±20% of initial value
tan δ
200% or less of initial specified value
Leakage current
Initial specified value or less
Shelf Life
Marking
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
Black print on the case top.
Chip Type
Trade mark
Voltage
Lot No.
Plastic platform
B±0.2
Series
Capacitance
Pressure
relief vent
L±0.5
Dimensions
(µF)
Cap.
V
Code
(mm)
BD 12.5 16. 18. 20.
A 4.0 4.5 5.0 5.0
B 13.6 17.1 19.1 21.1
C 16.0 19.5 21.5 23.5
E 8.0 10.5 11.5 13.5
H 2.5 3.75 3.75 3.75
6.3
10
0J
1A
22 220
H±0.1
The lead terminal structure : The same bent
lead type (refer to p.60) that is currently
used on 10mm diameter and smaller parts, is
also available upon request.
In this case of the bent lead type, Q will be
put at the 11th digit of type numbering system.
Please ask for details.
16
25
1C
1E
Type numbering system (Example : 50V 330µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
UUN 1H 3 3 1 MNL 1 MS
Size code
Capacitance Tolerance(±20%)
Rated Capacitance(330µF)
Rated voltage(50V)
Series name
Type
Package code
Taping
MS
Tray
ZD
Configuration
φD
12.5 ~ 18
20
Code
NL
RL
35
50
63
100
1V
1H
1J
2A
12.5 × 13.5 100
33 330
12.5 × 16 150
47 470
12.5 × 13.5 130 12.5 × 13.5 140 16 × 16.5 180
100 101
12.5 × 13.5 180 12.5 × 16 230 16 × 16.5 270 18 × 21.5 310
220 221
12.5 × 13.5 270
16 × 16.5 330
18 × 16.5 400
16 × 21.5 400
18 × 21.5 440
330 331
12.5 × 13.5 310 16 × 16.5 370
18 × 16.5 450
16 × 21.5 450
18 × 21.5 540 20 × 21.5 590
470
471
12.5 × 13.5 270 12.5 × 13.5 340
16 × 16.5 420 16 × 16.5 490
18 × 21.5 590
20 × 21.5 640
1000
102
12.5 × 16 500 16 × 16.5 600
18 × 16.5 670 18 × 21.5 780
16 × 21.5 670
2200 222
18 × 16.5 740
16 × 21.5 740
18 × 21.5 830
3300 332
18 × 21.5 920
In this case, 6 will be put at 12th digit of type numbering system, " "
Frequency coefficient of rated ripple current
Cap.(µF)
Frequency
00 ~ 470
50 Hz
0.75
120 Hz
1.00
300 Hz
1.35
1 kHz
1.57
100 ~ 470
0.80
1.00
1.23
1.34
1000 ~ 3300
0.85
1.00
1.10
1.13
10 kHz~
2.00
1.50
1.15
Case size Rated
φ D × L (mm) Ripple
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Please refer to page 3 for the minimum order quantity.
CAT.8100V